NXP Semiconductors UM10301 PCA8565 Скачать руководство пользователя

Страница: 4 / 54

NXP Semiconductors

UM10301

User Manual for PCF85x3, PCF85x63, PCA8565, PCF2123, and

PCA21125

UM10301

All information provided in this document is subject to legal disclaimers.

User manual

Rev. 2.1 — 23 July 2015

4 of 54

2. Features

The NXP real-time clock portfolio includes types for low power, types for automotive and

other high temperature applications and applications that need additional RAM. A third

family of highly accurate temperature compensated real time clocks will be dealt with in a

separate application note. Designed for a range of demanding applications, these real-

time clocks/calendars are driven by a low-power 32.768 kHz quartz oscillator, use the

SPI or I

C-bus for serial data transfer, and typically consume less than 1 μW of power.

Key features

•

Oscillator requires 32.768 kHz external quartz crystal

•

Resolution: seconds, minutes, hours, weekday, day, month, and year in 12- or 24-

hour (military) format. All time and alarm registers are in BCD format. Two types

include a 1/10

and 1/100

second resolution register

•

Clock operating voltage: 1.0 V to 5.5 V or wider, see Table 2

•

Low backup current: Ranging from 100 nA to 2 μA at V

= 1 V and T

amb

= 25 °C

•

Three line SPI with separate I/O or I

C serial interface

•

Freely programmable timer and alarm functions, each with interrupt capability

•

Freely programmable Watchdog timer

•

Programmable clock output for peripheral devices: 32.768 kHz, 1024 Hz, 32 Hz and

1 Hz (not all types)

•

One or two integrated oscillator capacitors (connected to the output of amplifier

OSCO in case of only one integrated capacitor)

•

Internal power-on reset

•

Open-drain interrupt pin

•

Wide variety of packages available including naked die

Addresses and data are transferred serially via an SPI bus with a maximum speed of 7.0

Mbps (PCF2123, PCA21125) or via a two-line, bidirectional I

C-bus that operates at a

maximum speed of 400 kbps (Fast-Mode, PCF8563 and PCA8565) or 100 kbps

(Standard-Mode, PCF8583 and PCF8593). The built-in word address register is

incremented automatically after each data byte is written or read.
With the PCF8583, the address pin A0 is used to program the software address, so that

two devices can be connected to the same I

C-bus without additional hardware.

Each RTC has an internal power-on reset and a programmable clock output with open

drain configuration to drive peripheral devices. A low voltage detector (not included on

the PCF8583,93 and PCA21125) warns if the integrity of all clock functions is no longer

guaranteed.
Power consumption is kept to a minimum in all the devices. The PCF2123 and PCF8563,

optimized for battery-powered applications, consume as little as 100 nA at 2 V and

250 nA at 1 V respectively. With careful selection of the crystal used, the PCF2123

consumes less than 100 nA on a 1.5 V supply.
The seconds, minutes, hours, days, weekdays, months, years as well as the minute

alarm, hour alarm, day alarm and weekday alarm registers are all coded in Binary Coded

Decimal (BCD) format. This format is popular with RTCs for the reason that time and

date in BCD format can easily be displayed in human-readable style without conversion.

Содержание UM10301 PCA8565























































Результаты поиска

Содержание UM10301 PCA8565

Отзывы:

Похожие инструкции для UM10301 PCA8565

Бренды по названию

Популярные бренды

NXP Semiconductors UM10301 PCA8565, Руководство пользователя

Результаты поиска

Содержание UM10301 PCA8565

Отзывы:

Похожие инструкции для UM10301 PCA8565

Бренды по названию

Популярные бренды