background image

 

6

 

REPLACEMENT OF MEMORY IC 

 
1. MEMORY IC. 

This TV uses memory IC. In the memory IC are memorized data for correctly operating the video and 

deflection circuits. 

When replacing memory IC, be sure to use IC written with the initial value of data. 

 

2.  PROCEDURE FOR REPLACING MEMORY IC 

(1) Power off 

Switch the power off and unplug the power cord from AC outlet. 

(2) Replace IC 

Be sure to use memory IC written with the initial data values. 

(3) Power On 

Plug the power cord into the AC outlet and switch the power On. 

(4)  Check and set SYSTEM default value: 

3.  Note: enter a factory mode method 

1)  Factory remote control: Press the factory remote control [TEST] key, appear on the television 

screen 'FACTORY'.  

2)  Customer remote control 

3)  Press [menu] key, appear the picture menu, press few character keys 6483, the screen appears 

'FACTORY'. press few character keys 6483 again, the screen appears '

 

B.W BALANCE '. 

4)  Press [menu] key, The “ADJUST” will be displayed on the screen. 

5)  Press [menu] key, withdraw factory mode.   

6)  Check the setting value of the SYSTEM default value of Table below. If the value is different, 

select items by [CH+]/[CH-] keys and set value by [VOL+]/[VOL-] keys. 

7)  Press “menu” key again and return to the normal screen.  

 
SERVICE ADJUSTMENT 

 
B1 POWER SUPPLY 

1.  Receive normal colour bar signal. 

2.  Connect DC voltmeter to VD551- and isolated ground. 

3.  Adjust potentiometer in power unit  to get the voltage as 110V ±1.0V for 21 inch hereinafter, 

                                                                                                   130 ±1.0V for 25 inch upwards. 

FOCUS ADJUSTMENT 

1.  Receive a crosshatch signal. 

2.  While watching the screen, adjust the FOCUS VR to make the vertical and horizontal lines as fine and 

sharp as possible. 

BUS CONTROL ADJUSTMENT 

To enter BUS control mode, Press “TEST” key on the Remote control unit of factory. 

Customer remote 

control press "MENU" key behind in a row press"6""4""8""3"

  

Choose a "SETUP SELECT" options in"P5" menu, setup the item of " ENG.PAGE " to "1”, press "MUTE" key 

again can depend on this get into "P5"~"P15" and "PP1. PP2. LANG. LANGX" of design menu, general 

Содержание TDA11106 Series

































Отзывы: