manualshive.com logo in svg

NXP Semiconductors QorIQ T1040, Руководство пользователя, Страница: 57 / 68

Поделиться
Скачать
NXP Semiconductors QorIQ T1040 Скачать руководство пользователя страница 57

4.2 Ethernet port map

The table below shows how Ethernet ports match to Linux, U-Boot, and the front-panel
label on the 1U box.

Table 4-1. Ethernet mapping table

Label on 1U
box

Port in U-Boot

Port in Linux

FMan address

Type

Internal port

FM1@DTSEC1 

1

fm1-gb0

Internal port

FM1@DTSEC2 

1

fm1-gb1

ETH0

FM1@DTSEC4

fm1-gb3

0xfe4e6000

RGMII

ETH1

FM1@DTSEC5

fm1-gb4

0xfe4e8000

RGMII

ETH2

FM1@DTSEC3

fm1-gb2

0xfe4e4000

SGMII

ETH3

Not supported in U-Boot

0xfe4e0000

L2 switch

ETH4

Not supported in U-Boot

L2 switch

ETH5

Not supported in U-Boot

L2 switch

ETH6

Not supported in U-Boot

L2 switch

ETH7

Not supported in U-Boot

0xfe4e2000

L2 switch

ETH8

Not supported in U-Boot

L2 switch

ETH9

Not supported in U-Boot

L2 switch

ETH10

Not supported in U-Boot

L2 switch

1. Connected to L2 switch port at 2.5 Gbit/s. This port cannot be connected to external PHYs, as T1040RDB supports only

SerDes protocol, 0x66

NOTE

ETH3-ETH10 belong to the switch. They are not visible as
interfaces in Linux. Switch control software is required to
control them.

4.3 NOR flash image layout

NOR flash can be divided into two flash banks (0 and 4) to store a main image and an
alternative backup image. This is shown in the below table.

Chapter 4 Software configuration

QorIQ T1040 Reference Design Board User Guide, Rev. 0, 06/2015

Freescale Semiconductor, Inc.

57

Содержание QorIQ T1040





































































Отзывы:

Нет отзывов