manualshive.com logo in svg

NXP Semiconductors MPC5566, Справочное руководство

Поделиться
Скачать
NXP Semiconductors MPC5566 Скачать руководство пользователя страница 1030

Enhanced Serial Communication Interface (eSCI)

MPC5566 Microcontroller Reference Manual, Rev. 2

Freescale Semiconductor

21-33

21.4.8.2

Disabling the eSCI

The module disable bit (ESCIx_CR2[MDIS]) in the eSCI control register 2 can be used to turn off the 
eSCI. This saves power by stopping the eSCI core from being clocked. By default the eSCI is enabled 
(ESCIx_CR2[MDIS]=0).

21.4.9

Interrupt Operation

Only the eSCI originates interrupt requests. The following sections describe how the eSCI generates a 
request and how the MCU acknowledges that request. The eSCI only has a single interrupt line (eSCI 
interrupt signal, active high operation) and all the following interrupts, when generated, are ORed together 
and issued through that port.

21.4.9.1

Interrupt Sources

There are several interrupt sources that can generate an eSCI interrupt to the CPU. They are listed with 
details and descriptions in 

Table 21-21

.

Table 21-21. eSCI Interrupt Flags, Sources, Mask Bits, and Descriptions

Interrupt 

Source

Flag

Description

Source

Local 

Enable

Transmitter

TDRE

Indicates that a byte was transferred from ESCIx_DR to the transmit 
shift register. The transmit data register empty (TDRE) interrupt is set 
high by the eSCI when the transmit shift register receives data, 8 or 9 
bits, from the eSCI data register, ESCI

x

_DR. A TDRE interrupt 

indicates that the transmit data register (ESCI

x

_DR) is empty and that 

a new data can be written to the ESCI

x

_DR for transmission. The 

TDRE bit is cleared by writing a one to the TDRE bit location in the 
ESCI

x

_SR.

ESCI

x

_SR[0]

TIE

Transmitter

TC

Indicates that a transmit is complete. The transmit complete (TC) 
interrupt is set by the eSCI when a transmission has completed. A TC 
interrupt indicates that there is no transmission in progress. TC is set 
high when the TDRE flag is set and no data, preamble, or break 
character is being transmitted. When TC is set, the TXD pin becomes 
idle (logic 1). The TC bit is cleared by writing a one to the TC bit 
location in the ESCI

x

_SR.

ESCI

x

_SR[1]

TCIE

Receiver

RDRF

Indicates that received data is available in the eSCI data register. The 
receive data register full (RDRF) interrupt is set when the data in the 
receive shift register transfers to the eSCI data register. An RDRF 
interrupt indicates that the received data has been transferred to the 
eSCI data register and that the received data can now be read by the 
MCU. The RDRF bit is cleared by writing a one to the RDRF bit 
location in the ESCI

x

_SR.

ESCI

x

_SR[2]

RIE

Receiver

IDLE

Indicates that receiver input has become idle. The idle line (IDLE) 
interrupt is set when 10 consecutive logic 1s (if M = 0) or 11 
consecutive logic 1s (if M = 1) appear on the receiver input. After the 
IDLE is cleared, a valid frame must again set the RDRF flag before an 
idle condition can set the IDLE flag.

 

The IDLE bit is cleared by writing 

a one to the IDLE bit location in the ESCI

x

_SR.

ESCI

x

_SR[3]

ILIE

Содержание MPC5566





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды