manualshive.com logo in svg

NXP Semiconductors MCF5253, Справочное руководство

Поделиться
Скачать
NXP Semiconductors MCF5253 Скачать руководство пользователя страница 546

Universal Serial Bus Interface

MCF5253 Reference Manual, Rev. 1

24-84

Freescale Semiconductor

 

Figure 24-50. Asynchronous Schedule List with Annotation to Mark Head of List

24.9.9.4

Asynchronous Schedule Traversal: Start Event

Once the host controller has idled itself using the empty schedule detection, it naturally activates and 
begins processing from the Periodic Schedule at the beginning of each micro-frame. In addition, it may 
have idled itself early in a micro-frame. When this occurs (idles early in the micro-frame) the host 
controller must occasionally reactivate during the micro-frame and traverse the asynchronous schedule to 
determine whether any progress can be made. Asynchronous schedule Start Events are defined to be:

•

Whenever the host controller transitions from the periodic schedule to the asynchronous schedule. 
If the periodic schedule is disabled and the asynchronous schedule is enabled, then the beginning 
of the micro-frame is equivalent to the transition from the periodic schedule, or

•

The asynchronous schedule traversal restarts from a sleeping state.

24.9.9.5

Reclamation Status Bit (USBSTS Register)

The operation of the empty asynchronous schedule detection feature depends on the proper management 
of the Reclamation bit in the USBSTS register. The host controller tests for an empty schedule just after it 
fetches a new queue head while traversing the asynchronous schedule. The host controller sets the 
Reclamation bit whenever an asynchronous schedule traversal Start Event occurs. The Reclamation bit is 
also set whenever the host controller executes a transaction while traversing the asynchronous 
schedule.The host controller clears the Reclamation bit whenever it finds a queue head with its H-bit set. 
The software should only set a queue head's H-bit if the queue head is in the asynchronous schedule. If the 
software sets the H-bit in an interrupt queue head, the resulting behavior is undefined. The host controller 
may clear the Reclamation bit when executing from the periodic schedule.

24.9.10 Managing Control/Bulk/Interrupt Transfers via Queue Heads

This section presents an overview of how the host controller interacts with queuing data structures.

Queue heads use the Queue Element Transfer Descriptor (qTD) structure defined in 

Section 24.8.5, 

“Queue Element Transfer Descriptor (qTD).”

USBSTS

Reclamation Flag

USBCMD

•

•

•

AsyncListAddr

01

Horizontal Ptr

0

1

H

•

•

•

Operational

Registers

Operational

Area

Horizontal Ptr

0

H

Operational

Area

0

H

Operational

Area

Typ T

01 0

Typ T

01 0

Typ T

Horizontal Ptr

List Head

Asynchronous Schedule

1: Transaction Executed
0: Head of List Seen

Содержание MCF5253









































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды