NXP Semiconductors MCF5253 Скачать руководство пользователя страница 518 | Manualshive

Страница: 518 / 648

NXP Semiconductors MCF5253 Скачать руководство пользователя страница 518

Universal Serial Bus Interface

MCF5253 Reference Manual, Rev. 1

24-56

Freescale Semiconductor

24.8.4.5

siTD Back Link Pointer

DWord 6 of a siTD is simply another schedule link pointer. This pointer is always zero, or references a
siTD. This pointer cannot reference any other schedule data structure.

24.8.5

Queue Element Transfer Descriptor (qTD)

This data structure is only used with a queue head. This data structure is used for one or more USB
transactions. This data structure is used to transfer up to 20480 (5

×

4096) bytes. The structure contains

two structure pointers used for queue advancement, a DWord of transfer state, and a five-element array of
data buffer pointers. This structure is 32 bytes (or one 32-byte cache line). This data structure must be
physically contiguous.

The buffer associated with this transfer must be virtually contiguous. The buffer may start on any byte
boundary. A separate buffer pointer list element must be used for each physical page in the buffer,
regardless of whether the buffer is physically contiguous.

Host controller updates (host controller writes) to stand-alone qTDs only occur during transfer retirement.
References in the following bit field definitions of updates to the qTD are to the qTD portion of a queue
head.

Table 24-49. siTD Buffer Pointer Page 1 (Plus)

Bit

Name

Description

31–12 Buffer

Pointer

(Page 1)

Bits [31–12] is a 4K page-aligned, physical memory addresses. These bits correspond to physical
address bits [31–12] respectively. The field P specifies the current active pointer

11–5 –

Reserved.

4–3

TP

Transaction position. This field is used with T-count to determine whether to send all, first, middle, or
last with each outbound transaction payload. The system software must initialize this field with the
appropriate starting value. The host controller must correctly manage this state during the lifetime of
the transfer. The bit encodings are:
00 All. The entire full-speed transaction data payload is in this transaction (that is, less than or equal

to 188 bytes).

01 Begin. This is the first data payload for a full-speed transaction that is greater than 188 bytes.
10 Mid. This is the middle payload for a full-speed OUT transaction that is larger than 188 bytes.
11 End. This is the last payload for a full-speed OUT transaction that was larger than 188 bytes.

2–0

T-Count

Transaction count. The software initializes this field with the number of OUT start-splits this transfer
requires. Any value larger than 6 is undefined.

Table 24-50. siTD Back Link Pointer

Bit

Name

Description

31–5

Back Pointer

This field is a physical memory pointer to a siTD.

4–1

–

Reserved. This field is reserved for future use. It should be cleared.

0 T

Terminate
0 siTD Back Pointer field is valid
1 siTD Back Pointer field is not valid

«
...
516
517
518
519
520
...
»

Содержание MCF5253









































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды