manualshive.com logo in svg

NXP Semiconductors MCF5253, Справочное руководство, Страница: 458 / 648

Поделиться
Скачать
NXP Semiconductors MCF5253 Скачать руководство пользователя страница 458

Advanced Technology Attachment Controller (ATA)

MCF5253 Reference Manual, Rev. 1

23-32

Freescale Semiconductor

 

This register contains the threshold to generate fifo_rcv_alarm and fifo_tx_alarm to the DMA interface.

•

If (fifo_tx_enable == 1 && fifo_fill < fifo_alarm): fifo_tx_alarm is set 1, request is made to DMA 
to refill fifo.

•

If (fifo_rcv_alarm == 1 && fifo_fill >= fifo_alarm): fifo_rcv_alarm is set 1, request is made to 
DMA to empty fifo.

23.5.2.7

Drive Registers Connected to ATA Bus

Some registers are addressable, but are not present in the ATA interface module. A list is given in 

Table 23-14

. If a read or write access is made to one of these registers, the read or write is mapped to a PIO 

read or write cycle on the ATA bus, and the corresponding register in the device attached to the ATA bus 
is accessed.

If the drive_data

 

register is accessed while the ATA interface operates in big endian mode, the bytes 

to/from the ATA bus are swapped. No swaps occur in little endian mode, nor for any other register.

23.6

Functional Description

The ATA interface provides two ways to communicate with the ATA peripherals connected to the ATA bus.

Address MBAR2 + 0x834 (FIFO_ALARM)

Access: User read/write

7

6

5

4

3

2

1

0

R

FIFO_ALARM[7:0]

W

Reset

0

0

0

0

0

0

0

0

Figure 23-43. FIFO_Alarm Register

Table 23-14. Drive Registers Connected to ATA Bus

Address

Name

Description

Access

MBAR2 + 0x8A0 (DRIVE_DATA)

drive_data

Drive data register

R/W

MBAR2 + 0x8A4 (DRIVE_FEATURES)

drive_features

Drive features register

R/W

MBAR2 + 0x8A8 (DRIVE_SECTOR_COUNT)

drive_sector_count

Drive sector count register

R/W

MBAR2 + 0x8AC (DRIVE_SECTOR_NUM)

drive_sector_num

Drive sector number register

R/W

MBAR2 + 0x8B0 (DRIVE_CYL_LOW)

drive_cyl_low

Drive cylinder low register

R/W

MBAR2 + 0x8B4 (DRIVE_CYL_HIGH)

drive_cyl_high

Drive cylinder high register

R/W

MBAR2 + 0x8B8 (DRIVE_DEV_HEAD)

drive_dev_head

Drive device head register

R/W

MBAR2 + 0x8BC (DRIVE_COMMAND)

drive_command

Drive command register

Write-only

MBAR2 + 0x8BC (DRIVE_STATUS)

drive_status

Drive status register

Read-only

MBAR2 + 0x8D8 (DRIVE_ALT_STATUS)

drive_alt_status

Drive alternate status register

Read-only

MBAR2 + 0x8D8 (DRIVE_CONTROL)

drive_control

Drive control register

Write-only

Содержание MCF5253









































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов