manualshive.com logo in svg

NXP Semiconductors MCF5253, Справочное руководство

Поделиться
Скачать
NXP Semiconductors MCF5253 Скачать руководство пользователя страница 108

Synchronous DRAM Controller Module

MCF5253 Reference Manual, Rev. 1

7-4

Freescale Semiconductor

 

7.3.1

DRAM Controller Registers

The DRAM controller registers memory map is shown in 

Table 7-3

.

.

7.3.1.1

DRAM Control Register (DCR) (Synchronous Mode)

The DRAM control register (DCR), 

Figure 7-3

, controls refresh logic.

Table 7-3. DRAM Controller Registers

MBAR

Offset 

[31:24]

[23:16]

[15:8]

[7:0]

0x100

DRAM control register (DCR) [

Section 7.3.1, “DRAM Controller Registers”

]

Reserved

0x104

Reserved

0x108

DRAM address and control register 0 (DACR0) [See 

Section 7.3.1.2, “DRAM Address and Control (DACR0) 

(Synchronous Mode)”

]

0x10C

DRAM mask register block 0 (DMR0) [See 

Section 7.3.1.3, “DRAM Controller Mask Registers (DMR0)”

]

0x110

Reserved

0x114

Reserved

Address MBAR + 0x100

Access: User read/write

 

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

R

SO

NAM

COC

IS

RTIM

RC

W

Reset

0

–

–

–

–

–

–

–

–

–

–

–

–

–

–

–

Figure 7-3. DRAM Control Register (DCR) (Synchronous Mode)

Table 7-4. DRAM Control Register (DCR) Field Descriptions (Synchronous Mode)

Field

Description

15

SO

Synchronous operation. Selects synchronous or asynchronous mode. When in synchronous mode, the DRAM 
controller can be switched to ADRAM mode only by resetting the MCF5253.
0

Asynchronous DRAM. Default at reset. Do not use.

1

Synchronous DRAM

Note: bit setting SO = 0 is a legacy mode. Do not use. First action must always be to set this bit.

14

Reserved, should be cleared. 

13

NAM

No address multiplexing. Some implementations require external multiplexing. For example, when linear addressing 
is required, the DRAM should not multiplex addresses on DRAM accesses. 
0

The DRAM controller multiplexes the external address bus to provide column addresses.

1

The DRAM controller does not multiplex the external address bus to provide column addresses.

12

COC

Command on SDRAM clock enable (BCLKE). Implementations that use external multiplexing (NAM = 1) must 
support command information to be multiplexed onto the SDRAM address bus.
0

BCLKE functions as a clock enable; self-refresh is initiated by the DRAM controller through DCR[IS]. 

1

BCLKE drives command information. Because BCLKE is not a clock enable, self-refresh cannot be used (setting 

DCR[IS]). Thus, external logic must be used if this functionality is desired. External multiplexing is also responsible 
for putting the command information on the proper address bit.

Содержание MCF5253









































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды