manualshive.com logo in svg

NXP Semiconductors MC9S08PA4, Справочное руководство

Поделиться
Скачать
NXP Semiconductors MC9S08PA4 Скачать руководство пользователя страница 110

5.4.1 IPC Status and Control Register (IPC_SC)

This register contains status and control bits for the IPC.

Address: 3Eh base + 0h offset = 3Eh

Bit

7

6

5

4

3

2

1

0

Read

IPCE

0

PSE

PSF

0

0

IPM

Write

PULIPM

Reset

0

0

1

0

0

0

0

0

IPC_SC field descriptions

Field

Description

7

IPCE

Interrupt Priority Controller Enable

This bit enables/disables the interrupt priority controller module.

0

Disables IPCE. Interrupt generated from the interrupt source is passed directly to CPU without
processing (bypass mode). The IPMPS register is not updated when the module is disabled.

1

Enables IPCE and interrupt generated from the interrupt source is processed by IPC before passing to
CPU.

6

Reserved

This field is reserved.
This read-only field is reserved and always has the value 0.

5

PSE

Pseudo Stack Empty

This bit indicates that the pseudo stack has no valid information. This bit is automatically updated after
each IPMPS register push or pull operation.

4

PSF

Pseudo Stack Full

This bit indicates that the pseudo stack register IPMPS register is full. It is automatically updated after
each IPMPS register push or pull operation. If additional interrupt is nested after this bit is set, the earliest
interrupt mask value(IPM0[1:0]) stacked in IPMPS will be lost.

0

IPMPS register is not full.

1

IPMPS register is full.

3

PULIPM

Pull IPM from IPMPS

This bit pulls stacked IPM value from IPMPS register to IPM bits of IPCSC. Zeros are shifted into bit
positions 1 and 0 of IPMPS.

0

No operation.

1

Writing 1 to this bit causes a 2-bit value from the interrupt priority mask pseudo stack register to be
pulled to the IPM bits of IPCSC to restore the previous IPM value.

2

Reserved

This field is reserved.
This read-only field is reserved and always has the value 0.

IPM

Interrupt Priority Mask

This field sets the mask for the interrupt priority control. If the interrupt priority controller is enabled, the
interrupt source with an interrupt level (ILRxx) value that is greater than or equal to the value of IPM will be
presented to the CPU. Writes to this field are allowed, but doing this will not push information to the

Table continues on the next page...

Interrupt priority control register

MC9S08PA4 Reference Manual, Rev. 5, 08/2017

110

NXP Semiconductors

Содержание MC9S08PA4


















































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды