NXP Semiconductors LPC5410x Скачать руководство пользователя | Manualshive

Страница: 281 / 463

background image

UM10850

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2016. All rights reserved.

User manual

Rev. 2.4 — 13 September 2016

282 of 464

NXP Semiconductors

UM10850

Chapter 22: LPC5410x Serial Peripheral Interfaces (SPI0/1)

22.4 Pin description

The SPI signals are movable functions and are assigned to external pins via IOCON. See

. Recommended IOCON settings are shown in

.

Table 319: SPI Pin Description

Function

I/O Description

SPI0_SCK

I/O Serial Clock. SCK is a clock signal used to synchronize the transfer of data. It is driven by the master

and received by the slave. When the SPI interface is used, the clock is programmable to be
active-high or active-low. SCK only switches during a data transfer. It is driven whenever the Master bit
in CFG equals 1, regardless of the state of the Enable bit.

SPI0_MOSI

I/O Master Out Slave In. The MOSI signal transfers serial data from the master to the slave. When the SPI

is a master, it outputs serial data on this signal. When the SPI is a slave, it clocks in serial data from
this signal. MOSI is driven whenever the Master bit in SPInCfg equals 1, regardless of the state of the
Enable bit.

SPI0_MISO

I/O Master In Slave Out. The MISO signal transfers serial data from the slave to the master. When the SPI

is a master, serial data is input from this signal. When the SPI is a slave, serial data is output to this
signal. MISO is driven when the SPI block is enabled, the Master bit in CFG equals 0, and when the
slave is selected by one or more SSEL signals.

SPI0_SSEL0

I/O Slave Select 0. When the SPI interface is a master, it will drive the SSEL signals to an active state

before the start of serial data and then release them to an inactive state after the serial data has been
sent. By default, this signal is active low but can be selected to operate as active high. When the SPI is
a slave, any SSEL in an active state indicates that this slave is being addressed. The SSEL pin is
driven whenever the Master bit in the CFG register equals 1, regardless of the state of the Enable bit.

SPI0_SSEL1

I/O Slave Select 1.

SPI0_SSEL2

I/O Slave Select 2.

SPI0_SSEL3

I/O Slave Select 3.

SPI1_SCK

I/O Serial Clock.

SPI1_MOSI

I/O Master Out Slave In.

SPI1_MISO

I/O Master In Slave Out.

SPI1_SSEL0

I/O Slave Select 0.

SPI1_SSEL1

I/O Slave Select 1.

SPI1_SSEL2

I/O Slave Select 2.

SPI1_SSEL3

I/O Slave Select 3.

Table 320: Suggested SPI pin settings

IOCON
bit(s)

Type D pin

Type A pin

Type I pin

10

OD: Set to 0 unless open-drain output is desired.

Same as type D.

I2CFILTER: Set to 1.

9

SLEW: Generally set to 0. Setting to 1 at higher SPI rates
may improve performance.

Not used, set to 0.

I2CDRIVE: Set to 0

8

FILTEROFF: Generally set to 1.

Same as type D.

Same as type D.

7

DIGIMODE: Set to 1.

DIGIMODE: Set to 1.

DIGIMODE: Set to 1.

6

INVERT: Set to 0.

Same as type D.

Same as type D.

5

Not used, set to 0.

Same as type D.

I2CSLEW: Set to 1.

«
...
279
280
281
282
283
...
»

Содержание LPC5410x
















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LPC5410x

Бренд: Parker Страницы: 30

Бренд: Gardena Страницы: 17

Бренд: Badger Meter Страницы: 16

Бренд: Harpo Страницы: 35

Бренд: Hardi Страницы: 2

Бренд: IAI Страницы: 5

Бренд: Harmonic Drive Страницы: 85

Бренд: Rain Bird Страницы: 24

ESP-LXIVM Series

Бренд: Rain Bird Страницы: 16

Бренд: Vacon Страницы: 132

Бренд: +GF+ Страницы: 3

Бренд: D+H Страницы: 16

Бренд: CompuPro Страницы: 33

Бренд: Invacare Страницы: 44

Бренд: Fairchild Страницы: 4

HYGRASREG KH-10

Бренд: S+S Regeltechnik Страницы: 16

Бренд: Hanbay Страницы: 13

SetPro MV Series

Бренд: Gigarise Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды