NXP Semiconductors LPC2880 Скачать руководство пользователя

Страница: 268 / 362

UM10208_2

User manual

Rev. 02 — 1 June 2007

268 of 362

NXP Semiconductors

UM10208

Chapter 21: LPC2800 DADC

5.1 Stream I/O Configuration Register (SIOCR - 0x8020 0384)

This register also contains bits that affect the I

S In, I

S Out, and Dual DAC blocks. All but

one of its bits have fixed and prescribed states. Typically, this register is written once,
during system initialization (reset) code.

5.2 Dual Analog In Control Register

Table 302. Dual ADC registers

Name

Address

Description

Access Reset

value

SIOCR

0x8020 0384

Stream I/O Configuration Register.

This register

is shared with the I

S in, I

S out, and Dual DAC

blocks. The bit in this register that affects the Dual
ADC has a fixed/prescribed value.

R/W

0x180

DAINCTRL

0x8020 03A4

Dual Analog In Control Register.

Contains

control bits for the Single-to-Differential Converters
(SDs) and Programmable Gain Amplifiers (PGAs)

R/W

DADCCTRL 0x8020 03A8

Dual ADC Control Register.

Contains control bits

for the Dual Analog-to-Digital Converters

R/W

DECCTRL

0x8020 03AC

Decimator Control Register.

Contains control bits

for the decimator block.

R/W

DECSTAT

0x8020 03B0

Decimator Status Register.

This read-only

Table 303. Stream I/O Configuration Register (SIOCR - 0x8020 0384)

Bit(s) Name

Description

Reset
value

6:0

Reserved. Always write 1s to these bits

DAI_OE

This bit affects the I

S Input module (DAI). See

Section 19–4.1 on

page 253

31:8

Reserved. Always write 0s to these bits. The value read from
reserved bits is not defined.

Table 304. Dual Analog In Control Register (DAINCTRL - 0x8020 03A4)

Bit(s) Name

Description

Reset
value

RSD_PD

A 1 in this bit powers down the right single-to-differential converter.

LSD_PD

A 1 in this bit powers down the left single-to-differential converter.

Reserved

Always write a 1 to this bit.

6:3

RPGA_GAIN These bits control the gain of the RPGA. Values 0-7 3 dB

times the value of the field. Values 8-15 all 24 dB.

RPGA_PD

A 1 in this bit powers down the RPGA.

11:8

LPGA_GAIN

These bits control the gain of the LPGA. Values 0-7 3 dB
times the value of the field. Value 8-15 all 24 dB.

LPGA_PD

A 1 in this bit powers down the LPGA.

16:13 Reserved

Reserved, user software should not write ones to reserved bits. The
value read from a reserved bit is not defined.

Содержание LPC2880










































































































































































































































































































































































Результаты поиска

Содержание LPC2880

Отзывы:

Похожие инструкции для LPC2880

Бренды по названию

Популярные бренды

NXP Semiconductors LPC2880, Руководство пользователя

Результаты поиска

Содержание LPC2880

Отзывы:

Похожие инструкции для LPC2880

Бренды по названию

Популярные бренды