NXP Semiconductors LPC11U1x Скачать руководство пользователя | Manualshive

Страница: 450 / 523

background image

UM10462

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2016. All rights reserved.

User manual

Rev. 5.5 — 21 December 2016

450 of 523

NXP Semiconductors

UM10462

Chapter 24: LPC11U3x/2x/1x Appendix ARM Cortex-M0

not a normal branch operation and, instead, that the exception is complete. Therefore, it
starts the exception return sequence. Bits[3:0] of the EXC_RETURN value indicate the
required return stack and processor mode, as

shows.

24.3.4 Fault handling

Faults are a subset of exceptions, see

Section 24–24.3.3

. All faults result in the HardFault

exception being taken or cause lockup if they occur in the NMI or HardFault handler. The
faults are:

•

execution of an

SVC

instruction at a priority equal or higher than SVCall

•

execution of a

BKPT

instruction without a debugger attached

•

a system-generated bus error on a load or store

•

execution of an instruction from an XN memory address

•

execution of an instruction from a location for which the system generates a bus fault

•

a system-generated bus error on a vector fetch

•

execution of an Undefined instruction

•

execution of an instruction when not in Thumb-State as a result of the T-bit being
previously cleared to 0

•

an attempted load or store to an unaligned address.

Only Reset and NMI can preempt the fixed priority HardFault handler. A HardFault can
preempt any exception other than Reset, NMI, or another hard fault.

24.3.4.1 Lockup

The processor enters a lockup state if a fault occurs when executing the NMI or HardFault
handlers, or if the system generates a bus error when unstacking the PSR on an
exception return using the MSP. When the processor is in lockup state it does not execute
any instructions. The processor remains in lockup state until one of the following occurs:

•

it is reset

•

a debugger halts it

•

an NMI occurs and the current lockup is in the HardFault handler.

Table 422. Exception return behavior

EXC_RETURN

Description

0xFFFFFFF1

Return to Handler mode.

Exception return gets state from the main stack.

Execution uses MSP after return.

0xFFFFFFF9

Return to Thread mode.

Exception return gets state from MSP.

Execution uses MSP after return.

0xFFFFFFFD

Return to Thread mode.

Exception return gets state from PSP.

Execution uses PSP after return.

All other values

Reserved.

«
...
448
449
450
451
452
...
»

Содержание LPC11U1x












































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LPC11U1x

Бренд: LAE electronic Страницы: 7

Бренд: LAE electronic Страницы: 2

Бренд: Reer Страницы: 2

Бренд: AC Tech Страницы: 2

Бренд: V-TAC Страницы: 2

Бренд: QSC Страницы: 13

DYGIZONE GJD910

Бренд: GJD Страницы: 13

Бренд: Belimo Страницы: 6

Бренд: MSA Страницы: 309

Бренд: Azbil Страницы: 220

Бренд: dunkermotoren Страницы: 34

Бренд: cashco Страницы: 14

Бренд: ICP DAS USA Страницы: 130

70-0122-113E0-536

Бренд: Bray Страницы: 16

Бренд: FASTRON. Страницы: 7

HydroController HCW

Бренд: MAC3 Страницы: 48

Бренд: S&P Страницы: 2

Бренд: TELECO AUTOMATION Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды