NXP Semiconductors KITPF5200SKTEVM Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 51

NXP Semiconductors KITPF5200SKTEVM Скачать руководство пользователя страница 42

NXP Semiconductors

UM11636

KITPF5200SKTEVM evaluation board

1. Make sure that the board has the jumper’s configured in their default positions as

shown in

. The default configuration enables the board to be fully controlled

by the FRDM-KL25Z and the GUI.

Figure 7. KITPF5200SKTEVM default jumper configuration

2. Connect the power supply to J1 (VIN) and J4 (GND). The power supply should be set

to an initial value of 5.0 V and current limited to 1.0 A.

3. Verify that the FRDM-KL25Z board is firmly mounted to the KITPF5200SKTEVM

board. Also, make sure that the USB cable between the FRDM-KL25Z and the PC is

securely connected. This connection is critical because the USB port not only serves

as a communication channel between the PC and the FRDM-KL25Z board, but also

provides voltages and references to some onboard circuits and generates the VDDIO

reference for the IC.

6.2 Connecting the PF5200 to the GUI

The procedure for connecting the PF5200 to the GUI is as follows:

UM11636

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2021. All rights reserved.

User manual

Rev. 2 — 13 December 2021

42 / 51

«
...
40
41
42
43
44
...
»

Содержание KITPF5200SKTEVM




















































Отзывы:

Нет отзывов