manualshive.com logo in svg

NXP Semiconductors KITPF5200SKTEVM, Руководство пользователя, Страница: 2 / 51

Поделиться
Скачать
NXP Semiconductors KITPF5200SKTEVM Скачать руководство пользователя страница 2

NXP Semiconductors

UM11636

KITPF5200SKTEVM evaluation board

Revision history

Revision

Date

Description

UM11363 v.2

20211213

•

Global: fixed typos and corrected minor format issues

UM11363 v.1.1

20211110

•

Global: replaced KITPF52SKTFRDMEM by KITPF5200SKTEVM

•

Global: added 

Section 5.2.3.2.3

•

Section 4.2

: replaced "USB to SPI" by "USB to I

2

C"

•

Section 4.3

: updated 

Figure 1

 and 

Table 2

 (deleted SW2)

•

Section 4.3.9

: replaced "driven correctly by the GUI" by "configured correctly through I

2

C

using the GUI"

•

Section 5.1.1

: updated step 4 (replaced "v0.8.bin" by "v0.9;bin")

•

Section 6.4

: updated description

UM11363 v.1

20210707

Initial release

Table 1. Revision history

UM11636

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2021. All rights reserved.

User manual

Rev. 2 — 13 December 2021

2 / 51

Содержание KITPF5200SKTEVM




















































Отзывы:

Нет отзывов