NXP Semiconductors KITPF5200SKTEVM Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 51

NXP Semiconductors KITPF5200SKTEVM Скачать руководство пользователя страница 19

NXP Semiconductors

UM11636

KITPF5200SKTEVM evaluation board

• Device manager:

used to start communication with device, enter or exit test mode,

enable I

2

C CRC and I

2

C secure access, enable watchdog.

• Framework settings:

manages file import/export and framework configuration.

• Window log:

reports USB and Device communication events.

• USB and device status:

indicates if USB or device is connected or disconnected,

shows firmware and GUI version, displays current state of FS state machine. Click

Display button to refresh.

• Tools access bar:

provides quick access to the PF52 evaluation tools and features.

Note:

Power tool is currently not available.

• Tab content:

shows the content of each tool or tab. There may be more tabs, boxes, or

windows inside.

Figure 4. Framework window

5.2.3.1 Framework settings

The framework settings section appears at the top left corner of the framework (

).

It consists of five items:

•

File

•

View

•

Import/Export

•

NXP

•

Help

UM11636

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2021. All rights reserved.

User manual

Rev. 2 — 13 December 2021

19 / 51

«
...
17
18
19
20
21
...
»

Содержание KITPF5200SKTEVM




















































Отзывы:

Нет отзывов