manualshive.com logo in svg

NXP Semiconductors KE1xF Series, Справочное руководство

NXP Semiconductors KE1xF Series - это серия полупроводниковых устройств с высокой производительностью и надежностью. Здесь представлено подробное описание функций и характеристик в Reference Manual, который можно скачать бесплатно на manualshive.com. Пользовательские инструкции доступны для загрузки, обеспечивая удобство в использовании продукта.

Поделиться
Скачать
background image

25.2 Power Modes Description

The power management controller (PMC) provides multiple power options to allow the
user to optimize power consumption for the level of functionality needed.

Depending on the stop requirements of the user application, a variety of stop modes are
available that provide state retention, partial power down or full power down of certain
logic and/or memory. I/O states are held in all modes of operation. The following table
compares the various power modes available.

For Run and VLPR mode there is a corresponding wait and stop mode. Wait modes are
similar to ARM sleep modes. Stop modes (VLPS, STOP) are similar to ARM sleep deep
mode. The Very Low Power Run (VLPR) operating mode can drastically reduce runtime
power when the maximum bus frequency is not required to handle the application needs.

Stop mode entry is not supported directly from HSRUN and requires transition to Run
prior to an attempt to enter a stop mode.

The three primary modes of operation are Run, Wait and Stop. The WFI instruction
invokes both wait and stop modes for the chip. The primary modes are augmented in a
number of ways to provide lower power based on application needs.

Table 25-1. Chip power modes

Chip mode

Description

Core mode

Normal

recovery

method

Normal Run

Default mode out of reset; on-chip voltage regulator is on.

Run

-

High Speed Run Allows maximum performance of chip. In this state, the MCU is able to

operate at a faster frequency compared to normal run mode.

Run

-

Normal Wait -

via WFI

Allows peripherals to function while the core is in sleep mode, reducing
power. NVIC remains sensitive to interrupts; peripherals continue to be
clocked.

Sleep

Interrupt

Normal Stop -

via WFI

Places chip in static state. On-chip voltage regulator is in a low power
mode. LVD is off while maintaining LVR and POR protection. NVIC is
disabled; AWIC is used to wake up from interrupt; Peripheral clocks
are stopped. All SRAM is operating (content retained and I/O state
held). ADC and CMP are optional on.

Sleep Deep

Interrupt

VLPR (Very Low

Power Run)

On-chip voltage regulator is in a low power mode that supplies only
enough power to run the chip at a reduced frequency. Reduced
frequency Flash access mode (1 MHz); LVD off; internal oscillator
provides a low power 4 MHz source for the core, the bus and the
peripheral clocks.

Run

-

VLPW (Very

Low Power

Wait) -via WFI

Same as VLPR but with the core in sleep mode to further reduce
power; NVIC remains sensitive to interrupts (FCLK = ON). On-chip
voltage regulator is in a low power mode that supplies only enough
power to run the chip at a reduced frequency.

Sleep

Interrupt

Table continues on the next page...

Power Modes Description

Kinetis KE1xF Sub-Family Reference Manual, Rev. 4, 06/2019

648

NXP Semiconductors

Содержание KE1xF Series












































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для KE1xF Series

Warren Controls 313 Installation, Operation & Maintenance Instructions Manual preview
313
Бренд: Warren Controls Страницы: 16
Bartec MAK 3003 Manual preview
MAK 3003
Бренд: Bartec Страницы: 26
DayTronic 3700 Series Instruction Manual preview
3700 Series
Бренд: DayTronic Страницы: 22
ICP DAS USA I-7188XA User Manual preview
I-7188XA
Бренд: ICP DAS USA Страницы: 166
ICP DAS USA SMS-531 User Manual preview
SMS-531
Бренд: ICP DAS USA Страницы: 64
ICS Tunnel Master Jr Manual preview
Tunnel Master Jr
Бренд: ICS Страницы: 83
National Instruments sbRIO-9629 Quick Reference Manual preview
sbRIO-9629
Бренд: National Instruments Страницы: 2
Talgil DREAM 2 Manual preview
DREAM 2
Бренд: Talgil Страницы: 14
YASKAWA FSDrive-MV1000 Series Instructions For Use Manual preview
FSDrive-MV1000 Series
Бренд: YASKAWA Страницы: 260
YASKAWA iQpump1000 Installation & Start?Up Manual preview
iQpump1000
Бренд: YASKAWA Страницы: 114
YASKAWA MOTOMAN FS100 Operator'S Manual preview
MOTOMAN FS100
Бренд: YASKAWA Страницы: 20
YASKAWA yasnac lx3 Maintenance Manual preview
yasnac lx3
Бренд: YASKAWA Страницы: 152
YASKAWA MOTOMAN FS100 Option Addendum preview
MOTOMAN FS100
Бренд: YASKAWA Страницы: 20
YASKAWA MOTOMAN FS100 Instructions Manual preview
MOTOMAN FS100
Бренд: YASKAWA Страницы: 17
YASKAWA 1000-Series Technical Manual preview
1000-Series
Бренд: YASKAWA Страницы: 58
YASKAWA J1000 CIMR-JC series Cheat Sheet preview
J1000 CIMR-JC series
Бренд: YASKAWA Страницы: 2
YASKAWA SI-EP3 Technical Manual preview
SI-EP3
Бренд: YASKAWA Страницы: 58
Newport MM4005 User Manual preview
MM4005
Бренд: Newport Страницы: 417

Бренды по названию

Популярные бренды

Загрузить еще бренды