Warranty Service
Warranty service must be performed by an authorized service center,
usually center, usually a NXG speaker systems dealer or its authorized
agent. You may obtain a list of authorized service centers by contacting
NXG. All warranty repairs must be accompanied by the original bill of
sales. No other document is acceptable or is required. This warranty
gives you specific legal rights, and you may also have other rights which
vary from state to state.
NXG reserves the right to revise speaker system specifications without notice.
(Continued from front)
NXG Speakers Three-Year Limited Warranty
If the NXG speaker system proves to be defective in workmanship or materials within three years from the
date of the original customer’s purchase, we will, at our option, repair or replace the defective product.
Limitation of Implied Warranties
Any implied warranties, including warranties of merchantability and fitness for a particular purpose, are
limited in duration to the length of this warranty
.
Exclusion of Certain Damages
NXG’s liability for any defective product is limited to repair or replacement of the product at our option.
NXG shall not be liable for incidental or consequential damages of any kind or character because of
product defects. Some states do not allow limitations on how long an implied warranty lasts and/or do
not allow the exclusion or limitation of incidental or consequential damages, so the above limitations and
exclusions may not apply.
This Warranty Does Not Cover:
• Damage caused by abuse, accident, misuse, negligence, or improper operation.
• Any product whose serial number has been altered, defaced, or removed.
• Products that have been altered or modified.
• Normal wear and maintenance.
• Damages caused by shipping. (All claims for shipping damage must be made with the carrier.)
6. See Fig. 5. With the speaker wire attached
to the speaker, slide the speaker up inside
the cut-out hole. Center the speaker in the
cut-out hole and turn the four locking screws
clockwise until the speaker is drawn up
snugly to the wall board from behind,
clamping the speaker in place. Try to tighten
each screw equally. Replace the speaker
grill by gently pressing it into place.
New Construction
1. Determine speaker locations and mark
them on your plans for future reference.
2. If possible, run speaker wires after HVAC
and electrical wiring is in place.
3. Secure speaker wires in place along the
run with insulated staples only and be careful
not to pierce the wire’s insulation. Allow a bit
of slack for expansion of building materials.
4. Needless to say, the actual speakers
should not be installed until the wall board is
in place. In the meantime, leave several feet
of wire coiled up and secured at the back
side of the mounting hole.
5. To complete the installation follow steps 2
through 5 above.
Operational Check
After making all connections it’s a good idea
to make sure every thing is working properly.
Turn on your surround or stereo system
making sure the volume control is turned
down and that the balance control is in the
center position. Activate a musical or movie
source such as FM, a CD or DVD player.
Gently turn up the volume, you should hear
sound coming from your new NXG speakers.
If no sound is heard from any or all speakers,
switch off the system immediately and check
for open or loose connections, wrong polarity
or shorts, or proper source selection.
FIG. 5
Specifications
NX-C5.2-X
NX-C6.2X
Maximum Power Handling:
5 - 50 watts
5 - 80 Watts
Sensitivity:
90dB @ 1 watt/1 meter
90dB @ 1 watt/1 meter
Frequency Response:
65 Hz-21,000 Hz
55 Hz-21,000 Hz
Driver Complement:
5
1
/
4
˝ (133mm) compression-molded
6
1
/
2
˝ (165mm) compression-molded
mineral-filled polymer cone woofer
mineral-filled polymer cone woofer
with rubber surround
with rubber surround
3
/
4
˝ (19mm) metallic-anodized liquid-
3
/
4
˝ (19mm) pivoting liquid-cooled
cooled polycarbonate dome tweeter
titanium dome tweeter w/minimum
w/minimum diffraction tilt-swivel island
diffraction tilt-swivel island
Nominal Impedance:
8 ohms 8
ohms
Overall Dimensions:
8˝ (diameter) round x 3˝D
9˝ (diameter) round x 3˝D
Required Ceiling Cut-out:
6
1
/
2
˝ (diameter) round
7
1
/
2
˝ (diameter) round
16648 North 94th Street
Scottsdale, AZ 85260
1-800-733-0008
FIG. 4
