Package
Overview
Installation
1
2
3
4
Warning
and
Caution
■
If the product does not work properly, please contact your dealer or the nearest
service center. Never attempt to disassemble the camera yourself. (We shall not be
responsible for any problems caused by unauthorized repair or maintenance.)
■
Do not allow water or liquid intrusion into the camera.
■
In the use of the product, you must be
in
strict compliance with the electrical
safety regulations of the nation and region. When the product is mounted on wall
or ceiling, the device shall be firmly fixed.
■
Do
not
use
camera
beyond
specified
voltage
range
.
■
Do not drop the camera or subject it to physical shock.
■
Avoid touching the camera lens
.
■
If cleaning is necessary, please use clean cloth to wipe it gently.
■
Do not aim the camera at the sun or extra bright place.
■
Do not place the camera in extremely hot, cold (the operating temperature shall
be
-22
˚
F~144
˚
F
), dusty or damp locations, and do not expose it to high
electromagnetic radiation.
■
To avoid heat accumulation, good ventilation is required for operating
environment.
Camera
Quick
start
guide
CD
Plastic
plug
×4
Drill
template
Rubber plug
Screwdriver
4 tapping screws
■
Please read th
e
s
e
instruction
s
carefully before using the product and keep it
for further reference.
■
All the examples and pictures used here are for reference only.
■
The contents of this manual are subject to change without notice.
2
1
3
1
Ethernet
Connector
2
Audio Input (MIC)
3
Audio
Output (HP)
4
Alarm Input/Output
5
DC12V Power
Connector*
6 Zoom-*
7 Zoom+ *
8 Micro SD Card Slot
9 Reset
10 CVBS Interface (unavailable)
* Please make sure that the wall or ceiling is strong enough to withstand 3
times the weight of the camera.
* Please install the camera in the dry environment.
I
nstall
the
back
of
the lower
dome
in
less than 4 hours after removing it.
*
*
If
the
PoE
switch is
used
to
power
the
camera
,
DC12V
power supply
is not required
.
*
It
is
recommended
to
install
the
security cap for outdoor installation.
①
②
Attach the drill template to the place where you want to fix the camera
and then drill 4 screw holes and 1 cable hole (if you want to route the cables
through the ceiling) according to the drill template.
Trim Ring
∅
4
.6
mm
3
.
55 in
3.55 in
Do not remove the protection film until finishing the installation.
Figure 1
Figure 2
1
3
4
5
9
9
6
7
8
8
10
2
A
L
A
R
M
4 3 2 1
Se
cu
ri
ty c
ap
1--ALM-COM
2--ALM-OPEN
3--ALM-INA
4--ALM-GND
DC12V
A
L
A
R
M
4 3 2 1
Sensor
IPC
ALARM-INA
ALARM-GND
Alarm
Input
:
3
4
Alarm
Power
IPC
ALARM-COM
ALARM-OPEN
+
+
-
-
Alarm
Output
:
1
2
►
Connecting
Alarm Input/Output
(Type A)
(Type B)
*
Only some models support T/W button. If your camera doesn’t have these two buttons, please
skip 6 and 7.
NCT-
8
ML-OV21AF
Vandal Dome
Camera
Quick Start Guide
①
Loosen
the
nut
from
the
main
element.
②
Run
the
network
cable (without
RJ 45
connector) through
both
elements. Then
crimp
the
cable
with
RJ 45
connector
.
③
Connect
the
cable
to
the
hermetic
connector
.
Then
tighten
the
nut
and
the
main
cover
.
Rotate the trim ring
counter-
clockwise to remove it from the camera.
Camera Installation
►
►
Connecting Network Cable
