IE Network Connection
5
MENU
MENU
IPC
IPC
Network Cable
Network Cable
Network Cable
Switch
Router
Computer
Computer
●
Access the camera through
Xcel IP Utility
Here we take accessing IP camera via LAN for example. In
LAN,
there are two ways to access. 1. Access through
Xcel IP Utility
;
2. Directly Access through IE Browser
①
Make sure that the camera and the PC are well connected via LAN.
②
Find the
Xcel IP Utility
from the CD and then install it in the computer.
After that, run the
Xcel IP Utility
as shown below.
Device
Network
Search
Immediate
Refresh
name
name
name
IPC
IPC
IPC
unknown
unknown
unknown
192.168.226.201
192.168.1.2
192.168.1.3
80
80
80
9008
9008
9008
255.255.
255.255.
255.255.
Modify Network Parameter
Mac Address
IP Address
Modify
CE :98 :23 :75 :35 :22
192
.
168
.
226
. 201
255
.
255
.
255
. 0
192
.
168
.
226
. 1
i
Tip: Enter the administrator password, and
then modify the network parameters.
Total Device: 3
Local IP Address:192
.
168
.
1
.
4
Subnet Mask:255
.
255
.
255
.
0 Gateway: 192
.
168
.
1
.
1
DNS
：
210
.
21
.
196
.
6
Device Name Device Type
IP Address
Http Port
Data Port
Subnet
Product Model
About
Subnet Mask
Gateway
Restore IPC Default Configuration
③
Modify the IP address. The default IP address of this camera is
192.168.226.201. Click the information of the camera listed in the
above table to show the network information on the right hand.
Modify the IP address and gateway of the camera and make sure its
network address is in the same local network segment as that of the
computer. Please modify the IP address of your device according
to the practical situation.
Mac Address
IP Address
Modify Network Parameter
Modify
CE :98 :23 :75 :35 :22
192
.
168
.
1
. 201
255
.
255
.
255
. 0
192
.
168
.
1
. 1
Subnet Mask
Gateway
For example, the IP address of your computer is 192.168.1.4. So
the
IP address of the camera shall be changed to 192.168.1.X. After
modification, please input the password of the administrator and click
“Modify” button to modify the setting.
The default password of the administrator is “
123456
”.
④
Double-click the IP address and then the system will pop up the IE
browser to connect IP-CAM. After downloading Active X control, a
login window will pop up. Input the user name and password to login.
●
Directly Access Through IE
The default network settings are as shown below:
IP address: 192.168.226.201 HTTP:80
Subnet Mask: 255.255.255.0 Data Port:9008
Gateway: 192.168.226.1
You may use the above default settings when you log in the camera
for the first time.
①
Set the IP address of the PC and make sure the network segment
should be as the same as the default settings of IP-CAM. Open the
network and share center. Click “Local Area Connection” to pop up
the following window. Select “Properties” and then select Internet
protocol according to the actual situation (for example: IPv4).
Next, click “Properties” button to set the network of the PC.
②
Open the IE browser and input the default address of IP-CAM
and confirm. The IE browser will download Active X control
automatically.
③
After downloading Active X control, the login dialog box will
pop up.
④
Input the default username and password and then enter to view.
NCT-4M-MV2A450043000607 A0
The default username is
admin
; the default password is
123456
.
③
Route and connect the cables.
④
Secure the mounting base with camera to the wall with screws as
shown below.
Rotation 0°~350°
Pan 0°~360°
Tilt 0°~70°
⑤
Three-axis adjustment. Before adjustment, preview the image of
the camera on a monitor and then adjust the camera according to
the figure below to get an optimum angle.
⑥
Install the lower dome back to the camera and secure it with the
screws.
