Nuvico CT-2M-P30FHIR Скачать руководство пользователя страница 32

Страница: 32 / 44

• VIEW ANGLE SETUP

VIEW ANGLE SETUP

PANNING RANGE

FLIP : AUTO
TILT ANGLE LIMIT : 00



SAVE AND EXIT(ESC TO CANCEL)

FLIP

OFF, AUTO

OFF:

The dome camera moves until 90



vertically.

AUTO:

When the camera reaches the floor directly above the moving object, it will stop.

At that time, release the

Joystick

instantly and pull it down again to run the auto-flip

function. When you use the panning range, it is recommended to use the flip mode to AUTO.

TILT ANGLE LIMIT

-10



~ 10



This option is designed to limit the view angle as there is some obstruction in zooming out on
specific areas of the tilt angle.

NOTE:

Focus issues may occur in certain conditions.

PANNING RANGE

When the dome camera is installed near a wall, panning range can be limited by user.

PANNING RANGE SETUP

(CTRL KEY)

RIGHT LIMIT : 000.0

LEFT LIMIT        : 000.0
ENABLE            : OFF
SWAP              : OFF

AUTO PAN : ON
SAVE AND EXIT(ESC TO CANCEL)

1. Place the dome camera under 90 degree vertically.
2. Set “

RIGHT LIMIT

” by pushing the

Joystick

to the right.

3. Set “

LEFT LIMIT

” by pushing the

Joystick

to the left.

4. Set

“

ENABLE

” to ON to use.

To exchange the right and the left limit, set “

SWAP

” to ON.

To apply limits on the auto pan (endless panning), set “

AUTO PAN

” to ON.

Содержание CT-2M-P30FHIR












































Результаты поиска

Содержание CT-2M-P30FHIR

Отзывы:

Похожие инструкции для CT-2M-P30FHIR

Бренды по названию

Популярные бренды

Nuvico CT-2M-P30FHIR, Инструкция по эксплуатации

Результаты поиска

Содержание CT-2M-P30FHIR

Отзывы:

Похожие инструкции для CT-2M-P30FHIR

Бренды по названию

Популярные бренды