Nuvation Energy NUV100-CI-12-1 Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 109

background image

stack_fault_contactor_feedback_fail

▪

Fault that is generated when there is a mismatch between the contactor state and the
contactor feedback signal provided. Note that the feedback is provided through a GPI.

sc_fault_pi_interlock

▪

Fault that is generated when the interlock function of the Stack Switchgear unit’s internal
Power Interface module has been activated. In the Stack Switchgear unit, this is connected to
fuse indicator switches on the main fuses. This fault should only occur if the main fuses have
blown.



The Stack Switchgear unit’s e-stop circuit is unrelated to this interlock.

sc_fault_fault_pilot_state_mismatch

▪

Fault that is generated when the fault pilot state set by the Stack Switchgear unit’s internal
Stack Controller module does not match the detected state on the Stack Switchgear unit’s
internal Power Interface module

10.1.6.1. Initialization Issues

All of these faults are dependent on the stack bus communication between the Stack Switchgear
unit’s internal Stack Controller and Power Interface modules The following table summarizes these
initialization issues:

Fault

Initialization Issues

sc_fault_pi_interlock

Stack Bus failure

sc_fault_fault_pilot_state_mismatch

Stack Bus failure

stack_fault_coil_fail

Stack Switchgear unit’s internal Power Interface module’s AFE disabled*

stack_fault_contactor_feedback_fail

GPI not configured*
Stack Switchgear unit’s internal Power Interface module’s AFE disabled*
Stack Bus failure

* Note that these faults may occur if the Stack Switchgear configuration file is incorrectly modified.
Contact

[email protected]

for a valid configuration file for the Stack Switchgear.

10.1.7. Diagnostics Faults

stack_fault_cell_open_wire

▪

Fault indicating there is an open wire on an installed cell channel

▪

This can also trip due to misconfigured or incorrectly installed cells

stack_warn_cell_open_wire

▪

Warning triggering on the same data as

stack_fault_cell_open_wire

stack_fault_therm_circuit_fail

▪

Fault indicating there is a circuit failure on a thermistor channel on a Cell Interface

▪

This can also trip due to misconfigured or incorrectly installed thermistors

Nuvation Energy High-Voltage BMS - Product Manual

Document ID: NE-PM-003

87

Rev 1.2, 2021-03-03

Curie Update 1

«
...
89
90
91
92
93
...
»

Содержание NUV100-CI-12-1














































































































Отзывы:

Нет отзывов

Похожие инструкции для NUV100-CI-12-1

Бренд: Handicare Страницы: 32

Бренд: T-Verter Страницы: 121

Бренд: Happy Страницы: 10

Бренд: BADODOSECURITY Страницы: 8

Бренд: CALEFFI Страницы: 12

QuickSetter+ 132 Series

Бренд: CALEFFI Страницы: 5

Бренд: Samson Страницы: 48

Бренд: T&S Страницы: 5

Бренд: ZKTeco Страницы: 13

Бренд: UniPi Technology Страницы: 4

GECO LUX GECO60

Бренд: GiBiDi Страницы: 48

Бренд: MaintTech Страницы: 28

Бренд: GREER Company Страницы: 35

Бренд: Aichi Страницы: 54

Бренд: PS Automation Страницы: 4

Бренд: Anritsu Страницы: 54

Бренд: Governors America Страницы: 6

Бренд: SKF Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды