Nußbaum Hebetechnik 4.40H Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 32

Nußbaum Hebetechnik 4.40H Скачать руководство пользователя страница 4

Organising requirements

-

The instructions for use are constantly to be kept at the place of operation being at hand at
any time.

-

In addition to the instructions for use rules pertaining to other regulations i.e. accident
prevention and environmental rules are to be observed and directed.

-

Safety- and dangeralert operation of personal is occasionally and by observing the
instructions for use to be controlled.

-

As far as required and ordered by regulations personal protective equipment is to be used

-

All safety- and danger-hints at the lift are to be observed!

-

Spare parts must comply with technical requirements laid down by the manufacturer.
This is only warranted with original parts.

-

Consider time intervals given or fixed in instructions for use for repeated tests/inspections.

Maintenanceworks, remedy of faults and disposal

-

Fixed Adjusting-, maintenance- and inspectionworks and time intervals including details
for exchange of parts/part components as mentioned in the instructions for use are to be
adhered.
These works must only be carried out by expert personal.

-

After maintenance- and repair works loose screw connections must always be firmly
tightend!

Instruction and Documentation

4.40 H

4

«
...
2
3
4
5
6
...
»

Содержание 4.40H

































Отзывы:

Нет отзывов