Numatic CRO 8055 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 9

Numatic CRO 8055 Скачать руководство пользователя страница 6

Cleaning, emptying the machine

Always ensure that the machine is switched off prior to any maintenance.

The vac shut off system fitted to your machine stops the airflow when the top tank is full!

It does not shut the power off to the vac motor, the vac motor will continue to run, but there is an audible difference

in the sound when the shut off system operates.

Waste-water Tank Full

A

B

C

After use, empty waste-water tank using emptying hose and flush-out with

clean water.

Next remove floor-tool vacuum hose ensuring you remove the U-bend clip

and flush out with clean water.

Next empty clean water tank, using emptying hose and again flush out with

clean water.

A

B

C

Located in your waste water (top) tank is a vacuum shut off system, this prevents suction when the waste

water tank is full. It also prevents foam created by high-foaming detergents from entering the motor.

Sometimes the float vents get clogged and blocked, clean to ensure correct operation regularly check and

clean the air filter in the top of the assembly.

Remove debris basket filter and rinse using clean water, and refit.

IMPORTANT: If the debris basket is allowed to become clogged, vacuum performance can

deteriorate.

Fuses, Key, Floor tool

Brush, Brush deck, Filling

Controls, Brush Pressure, Stop button

Using the machine, Speed, Anti Tip

Empty waste water

Cleaning the machine, Hose clip

Changing floor tool blades

«
...
4
5
6
7
8
...
»

Содержание CRO 8055










Отзывы:

Нет отзывов