manualshive.com logo in svg

Numatic CRO 8055, Руководство по устранению неисправностей, Страница: 1 / 9

Поделиться
Скачать
Numatic CRO 8055 Скачать руководство пользователя страница 1

Trouble Shooting and Help Guide

CRO 8055

Floor

Care

Make sure you read and fully 

understand your CRO manual 

before using the machine.

The CRO has been designed to scrub and dry a variety of hard floors.

This machine has not been designed to pick up large objects, make sure you pre-sweep the floor before use.

For optimum performance make sure you keep the filters, hoses and floor tool blades clean and free from debris.

After every time the machine is used.

The machine should be left in a clean and tidy state, drain

all fluids, clean all filters, pipes and place the

battery on charge.

PROBLEM

CAUSE

SOLUTION

Machine will not operate

Fuses

Key in the ‘OFF’ position

Low battery charge

Stop button in ‘OFF’ mode

Connected and charging

Fit or replace fuse

Turn key to ‘ON’

Charge batteries

Reset stop button

Take off charge

Vacuum will not operate

Floor tool in raised position 

Lower floor-tool

Poor water pick-up

Waste-water tank full

Vacuum hose

Loose hose connections 

Debris basket filter

Poor separator seal

Damaged separator seal

Damaged vacuum hose

Damaged floor-tool blades

Low battery charge

Empty waste-water tank

Remove and clean

Push tight connections

Remove and clean

Clean and refit

Renew

Renew 

Renew

Recharge batteries

No brush / scrub function No brushes fitted

Brush deck raised

Check and fit

Lower brush deck

Little or no water flow

Clean-water tank empty

Clean-water tank filter

Incorrect water flow setting

Brush deck raised

Fill clean-water tank

Remove and clean

Adjust as desired

Lower brush deck

Machine just ‘stops’ while 

operating

Load on the brush system

Reset the machine

12

2

3

4

5

6

7

8

10

11

1

1

Operator control panel

10

On board charger

2

Brush deck foot pedal

11

Accelerator pedal

3

Anti-tip buffers

12 Pedestrian light

4

Floor tool raise and lower lever

13

Floor tool transit bracket

5

Clean water filling point

14

Air separator

6

Brush deck

15

Waste water emptying hose

7

40 Amp battery fuse

16

Vacuum hose

8

Gel batteries

17

Clean water emptying hose

9

Clean water tank filter

18

Floor tool

18

13

14

15

16

17

9

Fuses, Key, Floor tool

Brush, Brush deck, Filling

Controls, Brush Pressure, Stop button

Using the machine, Speed, Anti Tip

Empty waste water

Cleaning the machine, Hose clip

Charging

Changing floor tool blades

Содержание CRO 8055










Отзывы:

Нет отзывов