The Ultimate Party Machine
- Consumer Products Division
©1999 Numark Industries
- 7 -
http://www.numark.com
32.
Line Inputs - Unbalanced RCA jacks for connecting
external sources. The Phono/Line Input is selected
with the toggle switch on the front panel. You can
connect stereo audio from Turntables, HiFi VCRs,
cassette and reel-to-reel tape decks, DAT machines,
CD players, laser discs, tuners, even synthesizers or
other mixing consoles. NOTE: Plug mono audio
sources into both Left and Right inputs using a "Y"
cable connector.
33.
GND - Grounding lug for turntable connection.
Always use this connection when using turntables.
(your turntable cable should have a grounding wire)
34.
Phono input- Use this to plug in phono level
equipment (turntables). When Phono input is
selected, your signal is fed directly to phono pre-
amplifiers. Use this jack only for turntables. Line
level sources will overload the sensitive phono pre-
amps and will sound very bad.
35.
Power Switch – Turn on unit here.
36.
Power Connector - Plug in power adapter here and
check the voltage level to match your country’s
standard
SET UP
1.
Make sure the Ultimate Party Machine is switched
OFF.
2.
Connect the power to the unit and appropriate power
source.
3.
Connect the speakers using the supplied speaker
cables. Connect the socket in the rear of the left
speaker to the left speaker output (30), and connect
the right speaker socket to the right speaker output
(30).
4.
If you wish to use the microphone or headphones,
connect them to the appropriate jacks.
5.
Before switching on the power to Ultimate Party
Machine, ensure that all sliders and knobs are set
to the minimum, to avoid a sudden burst of sound.
6.
Now you can switch the power ON.
To Play a CD
7.
Select the CD1 and CD2 on the input toggles (11).
8.
Open the CD1 door by pressing the EJECT
button(6).
9.
Insert the CD and shut the door.
10.
Select the desired track with the track button(3).
11.
Play the CD by pressing the PLAY / PAUSE
button(1).
12.
Slide upwards the Channel 1 volume control (10).
13.
Move the crossfader (12) to the left (Channel 1).
14.
Position the master graphic equalizers (17) to their
mid - point.
15.
Slide up the Master Volume Control (16). You
should now hear sound from your speakers.
16.
Now you need to adjust the master graphic equalizer
(17) to your sound preference.
To MIX
17.
Set the headphone cue selector (21) to Channel 2.
18.
Repeat steps 8-13 on CD2.
19.
Increase the headphone volume control (20) to the
desired level.
20.
Pause (1) the CD where you want to start.
21.
When CD1 is ending, Press Play (1) on CD2.
22.
Move the crossfader (12) to the right (Channel 2).
23.
You should now hear CD2 in the speakers.
To use the Microphone
24.
Plug in Mic.
25.
Turn on Mic.
26.
Slide up Mic level.
27.
Slide up master level.
28.
Speak into Mic.
29.
Adjust Mic EQ to good sound.
TROUBLESHOOTING:
Symptom
Possible Cause
Corrective Action
The power fails to switch on when
the POWER switch is set to on
Poor power plug connection at the AC outlet or
Power cord loose from rear of unit
Insert the power plug firmly into the AC outlet
and make sure connection is good in unit rear
Disc play does not start
The disc is loaded upside down
The disc is too dirty
Reload the disc with the label side up
Clean the disc
No sound
Improper amplifier cable connections
Connect the output cables correctly
Sound skips
The CD player is still subject to vibrations or
physical shock
The disc is too dirty
Change the installation location
Clean the disc
Hum
Loose cable connections
Firmly connect all audio plugs
