background image

Interchanging the Pitch Fader and  

Button Cartridges 

 

The TTXUSB unique design allows the 
configuration of the PITCH FADER and BUTTON 

CONTROLS to be interchanged depending on the 
orientation of the turntable. In the event of 

damage or excessive wear, these components 
should only be replaced with NUMARK 

COMPATIBLE PARTS. Check the nearest NUMARK 
DEALER for additional information. 

 
1.

 

Turn the turntable off or unplug it from its 
power source. 

2.

 

Remove the PITCH FADER KNOB and store 
it in a safe place. 

3.

 

Use the included SERVICE TOOL to remove 
the two screws that secure the PITCH 

FADER CARTRIDGE PLATE. Once removed, 
place these screws in a safe place. 

4.

 

Use the flat side of the SERVICE TOOL to 
pry off the PITCH FADER CARTRIDGE PLATE 

by inserting it into the cutaway at the 
center of the plate and prying upwards 

5.

 

Use the included SERVICE TOOL to remove 
the two screws that secure the BUTTON 

CARTRIDGE PLATE. Once removed, place 
these screws in a safe place. 

6.

 

Using the flat side of the SERVICE TOOL 

again, pry off the BUTTON CARTRIDGE 
PLATE by inserting it underneath the plate 

and prying upwards (see picture.) 

7.

 

The cartridges may now be safely removed. 

Begin this process by using the flat side of 
the SERVICE TOOL to pry the PITCH FADER 

CARTRIDGE out of the turntable (see 
picture.) Once removed, detach the wiring 

clip from the bottom of the cartridge. 

8.

 

Remove the Button Cartridge now by using 

the SERVICE TOOL to pry out the cartridge 
from the turntable. Once removed, detach 

the wiring clip from the bottom of the 
cartridge (see picture.) 

9.

 

The cartridges may now be safely 
interchanged. Find the WIRING CLIP for the 

PITCH FADER CARTRIDGE and connect it to 
the bottom of the cartridge (see picture.) 

10.

 

Reinsert the PITCH FADER CARTRIDGE into 
the desired bay of the turntable. Take 
utmost care NOT to pinch the unused 

harness underneath the cartridge. If 
inserted correctly, the cartridge should rest 

firmly in the bay. 

11.

 

Find the WIRING CLIP for the BUTTON 

CARTRIDGE and connect it to the bottom of 
the cartridge (see picture.)   

12.

 

Reinsert the BUTTON CARTRIDGE into the 
desired bay of the turntable. Take utmost 

care NOT to pinch the unused harness 
underneath the cartridge. If inserted 

correctly, the cartridge should rest firmly in 
the bay. 

13.

 

Re-secure the BUTTON CARTRIDGE PLATE 
and the FADER CARTRIDGE PLATE by 
inserting the tabbed sides into the turntable 

first. 

14.

 

Use the included SERVICE TOOL to tighten 

the four screws that secure the plates to the 
turntable body. Do not over tighten these 

screws. 

15.

 

Reinstall the PITCH FADER knob and power 

the turntable on.

 

 

Содержание TTXUSB










Отзывы: