Numark Pro SMX, Быстрый старт

Страница: 5 / 24

3
How do I know if my ¼” cables
are balanced?
BALANCED
UNBALANCED
REAR PANEL FEATURES
1. POWER SWITCH – Turns the
mixer on and off. Turn on the
mixer after all input devices
have been connected and
before you turn on amplifiers.
Turn off amplifiers before you
turn off the mixer
2. DC IN – Use the included
power adapter to connect the
mixer to a power outlet. While
the power is switched off, plug
the power supply into the mixer
first, then plug the power
supply into a power outlet.
Note: The mixer is designed to work with the included DC power supply only. Using an incompatible power supply could
result in damage to the unit.
3. MASTER OUTPUT (BALANCED) – Connect this low-impedance XLR output to a PA system or powered monitors. The
level of this output is controlled with the MASTER knob on the top panel.
4. FX SEND – Connect the inputs of an external effects unit to these outputs
using ¼” cables.
5. FX RETURN – Connect the outputs of an external effects unit to these outputs
using ¼” cables.
6. AUX IN (RCA) – Connect line-level or phono devices to these inputs.
7. MASTER OUTPUT (RCA) – Use standard RCA cables to connect this output
to a speaker or amplifier system. The level of this output is controlled by the
MASTER knob on the top panel.
8. AUX / BOOTH OUTPUT (RCA) – Use standard RCA cables to connect this output to a booth amp or other monitoring
system. The level of this output is controlled by the AUX / BOOTH OUTPUT knob on the top panel.
9. LINE INPUTS (BALANCED) – Use standard ¼” cables to connect line-level
devices with balanced outputs, such as synths or keyboards, to these inputs.
10. LINE INPUTS (RCA) – Connect line-level devices, such as CD players,
samplers or audio interfaces, to these inputs.
11. LINE | PHONO INPUTS (RCA) – Connect your audio sources to these inputs.
These inputs can accept both line and phono-level signals.
12. LINE | PHONO SWITCH – Flip this switch to the appropriate position, depending on the device connected to the LINE |
PHONO INPUTS. If you are using phono-level turntables, set this switch to “PHONO” to provide the additional
amplification needed for phono-level signals. If using a line-level device, such as a CD player or sampler, set this switch
to “LINE.”
13. GROUNDING TERMINAL – If using phono-level turntables with a grounding wire, connect the grounding wire to these
terminals. If you experience a low “hum” or “buzz”, this could mean that your turntables are not grounded.
Note : Some turntables have a grounding wire built into the RCA connection and, therefore, nothing needs to be
connected to the grounding terminal.
FRONT PANEL FEATURES
1. MIC INPUT – Connect an XLR or ¼” microphone to
this input. Microphone controls are located on the top
panel.
2. CHANNEL FADER REVERSE – Changes the
direction of the corresponding channel fader. When
pressed, the audio level of the corresponding channel
will decrease when you move the fader up or increase
when you move the fader down.
3. CHANNEL FADER SLOPE – Adjusts the slope of the
CHANNEL FADERS. Turn to the left for a smooth
fade (mixing) or to the right for a sharp cut (scratching).
4. CROSSFADER (CF) MODE – Reverses the assignment of Channels 1 and 2 on the crossfader.
5. CROSSFADER (CF) SLOPE – Adjusts the slope of the CROSSFADER curve. Turn to the left for a smooth fade
(mixing) or to the right for a sharp cut (scratching).
6. HEADPHONES – Connect your ¼” or 1/8” headphones to these outputs for cueing and mix monitoring. Headphone
output controls are located on the top panel.
If nothing is connected to the FX
SEND or FX RETURN jacks, the
audio signal will be automatically
bridged between them. This way,
the signal will be uninterrupted if
the
FX SEND switch is
accidentally engaged.
1
2
3
5 4 7 8 9 10 11
13
12
9 10 11
13
12
6
1
2 2
3 3 5 5
6
4