background image

 

20 

 Product Warranty / Service 

Product Warranty/Service 

Seller warrants that equipment furnished will be free form defects in 
material and workmanship for a period of one year from the confirmed 
date of purchase of the original buyer and that upon written notice of any 
such defect, Seller will, at its option, repair or replace the defective item 
under the terms of this warranty, subject to the provisions and specific 
exclusions listed herein. 
 
This warranty shall not apply  to equipment that has been previously 
repaired or altered outside our plant in any way as to, in the judgment of 
the manufacturer, affect its reliability. Nor will it apply if the equipment 
has been used in a manner exceeding its specifications or if the serial 
number has been removed. 
 
Seller does not assume any liability for consequential damages as a 
result from our products uses, and in any event our liability shall not 
exceed the original selling price of the equipment. 
 
The equipment warranty shall constitute the sole and exclusive remedy 
of any Buyer of Seller’s equipment and the sole and exclusive liability of 
the Seller, its successors or assigns, in connection with equipment 
purchased and in lieu of all other warranties expressed implied or 
statutory, including, but not limited to, any implied warranty of merchant 
ability or fitness and all other obligations or liabilities of seller, its 
successors or assigns. 
 
The equipment must be returned postage-prepaid. Package it securely 
and insure it. You will be charged for parts and labor if you lack proof of 
date of purchase, or if the warranty period is expired. 
 

Содержание ACL-7225B






























Отзывы: