manualshive.com logo in svg

Nu-Air Windsor NU145, Эксплуатация, обслуживание и установка

Поделиться
Скачать
Nu-Air Windsor NU145 Скачать руководство пользователя страница 16

 

 

Rev 6.1 November 1, 2016 

 

15 

3.1.2.

 

ES Lumina (p/n NAV-561) 

 
The Lumina offers a complete package of control options in one unit. This product replaces the ES-DVC 
March 2015. 

 

Features:  

•

 

Backlit LCD Screen 

•

 

Generously sized navigation keys 

•

 

Intuitive user interface 

•

 

Interchangeable face plate to mount chosen face plate colour 

•

 

On-board humidity sensor can be disabled where chosen 

•

 

Built-in 20-20-60-minute timer 

•

 

1-12 month runtime filter alert (factory default 3 mos.)  

•

 

Programming option for non-recirculation units

 

Functions:

  

Off, Standby, Continuous low speed, Continuous high speed, Intermittent high speed (with humidity 
call) Continuous recirculation, 20 Lo/40 standby, 20 Lo/40 recirculation  
 
Note: for units manufactured before March 2015 (XXXXX1503…), recirculation functions are to be 
turned off in “Settings”. The Lumina offers all other functions for older units. Upgrading to a circuit 
board with current firmware is the only option to access recirculation for these older units.  

3.1.3.

 

Wiring ES Series Controls 

 
Using a 3 mm flat head screwdriver, connect 4-conductor wire to the 12 
VDC (4-wire) removable terminal block provided. Wiring ES controls 
involves simply matching terminals on the control to those of the 
HRV/ERV terminal block (see right). 
 

 

DO NOT

 

cross the +12V/12 and ground (GND/G) wires

. For ES controls, doing so with power 

connected to the H/ERV might damage the ES wall control processor.  
 

Notes:  

1.

 

ES controls can be connected in 

SERIES

 or 

PARALLEL

.  

2.

 

24V control options discussed in this document may be used, but only ONE central control may be 
employed per installation.  

3.

 

If you are using 

ONLY ES-T1

 to control your unit, with no central controller, you must connect a 

jumper wire between R and SB on the 24V (10-wire) removable terminal block. In this situation you 
can add continuous low speed operation by connecting a jumper wire between R and LO. Consult 
local building code in case a centrally located control with an on/off switch is required. 

 
 
 
 
 

HRV/ERV 
TERMINAL 
BLOCK 

ES 
CONTROL 

G 

GND 

A 

A BUS 

B 

B BUS 

12 

+12V  

Содержание Windsor NU145


























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды