NTI RACK MOUNT CONSOLE TERMINAL WITH CONSOLE SWITCH
37
Comm Mode
sets the
SERIAL1
port communication mode to full duplex (FDX), block (BLK), half duplex (HDX), or half duplex
block (HBLK).
Multiple Sessions
defines whether an Ethernet connection supports multiple sessions function.
ON : indicates the terminal supports multiple sessions. Each session only has one display page. In 80 or 132 column mode, 8
simultaneous sessions are supported. In Econ-80 column mode, 12 simultaneous sessions are supported.
OFF : indicates the terminal only has single session. In this mode page length greater than one page can be defined.
F5
- Misc SETUP Menu
Wprt Intensity
sets the write protect attribute: normal, blank, dim, blank/dim.
Block End
causes the terminal to send a block of data to the CPU with a line terminator as an ASCII US character and block
terminator as an ASCII CR character (US / CR), or with line terminators as ASCII CR and LF characters and the block terminator
as an ASCII ETX character (CRLF / ETX).
Ptr Parity
causes the terminal to send the data to the
SERIAL 2 (printer)
port with none, odd, mark, even, or space parity.
Printer RCV
ON/OFF
Wprt Reverse
sets the write-protected characters to appear in reverse (dark characters on a light background).
Ptr Baud rate
sets the
SERIAL 2 (printer)
port baud rate to 75, 150, 300, 600, 1200, 2400, 4800, 7200, 9600, 19200, 38400,
57600, 76800, 115200, 230400, 460800.
Ptr Rcv Hndshake
sets the printer receive handshake through SERIAL 2 to be none, DTR, Xon / Xoff, DTR/Xoff .
Wprt Underline
sets the write-protected characters to appear underlined.
Ptr Data/Stop Bits
sets the data and stop bits through the
SERIAL 2
(printer) port.
Ptr Xmt Hndshake
sets the printer handshake to be none, DSR, Xon / Xoff, or Both .
F6
-Tabs SET-UP Menu
On the tabs setup menu screen, the terminal's current tab stops are indicated by uppercase T's displayed along a line of periods
that mark each column position.
(1) A tab stop in columns 2 through 78 is shown as a T in the upper line of periods
(2) A tab stop in columns 79 through 132 is shown as a T in the lower line of periods
The user can easily determine where tabs are set by moving the cursor across the line and reading the column number displayed
on the right side of the screen. Clear and set tabs anywhere on the line, as follows:
(1) To move the cursor across the line, press <
→
> (right arrow)
or <
←
>
(left arrow)
(2) To either clear or set (toggle) an individual tab stop at the cursor position, press <
Spacebar>
(3) To clear all tabs, press <
Home>
(4) To set tabs to the default setting (every eighth column), press <
Backspace>
Note: A tab stop cannot be set to column 1.
F7
- FKeys SET-UP Definition Setup Menu
The function keys and many of the editing keys can be redefined to send a unique character string of up to 64 characters. Keys
that are not programmed will send a default sequence, which is determined by the personality selected.
Table 4
lists the
programmable keys.
To redefine a key:
1. Select the key to be redefined by pressing that key together with <
Ctrl>.
This highlights the key's definition field.
2. Press < >
(up arrow)
to select the shifted or unshifted key definition field.
3. Enter the key definition (up to 62 characters) at the cursor position. Correct errors by pressing <
>
(left arrow) to
delete characters or <
Home>
to clear the definition.
4. If the user wants to change the key's direction, press <
Enter>
(on the numeric pad) until the desired choice appears.
Direction determines where the key data is transmitted:
- Remote: Sends data to the CPU only, regardless of the terminal's communication mode. (Until redefined, the
direction of all the programmable keys is remote.)
- Local: Sends data to the terminal only, regardless of the terminal's communication mode
-
Normal: Sends data to the CPU and / or the terminal, depending on the terminal's communication mode
