background image

LinMot Installation Guide C1100          

 13 Ordering Information

Drive

Description

Art. No.

C1100-GP-XC-0S-000

General Purpose Drive

72VDC/25A

peak

0150-2380

C1150-EC-XC-0S-000

ETHERCAT Drive 72VDC/25A

peak

0150-2382

C1150-PN-XC-0S-000

PROFINET Drive

72VDC/25A

peak

0150-2384

C1100-GP-XC-1S-000

General Purpose Drive

72VDC/25A

peak

/STO

0150-2381

C1150-EC-XC-1S-000

ETHERCAT Drive 72VDC/25A

peak

/STO

0150-2383

C1150-PN-XC-1S-000

PROFINET Drive

72VDC/25A

peak

/STO

0150-2385

Accessories

Description

Art. No.

DC01-C1X00-0S/X1/X4

Drive Connector Set for C1X00-0S

0150-3527

DC01-C1X00-1S/X1/X4/X33

Drive Connector Set for C1X00-1S

0150-3528

DC01-C1X00/X1

Drive Connector for PWR 72VDC Input

0150-3525

DC01-C1X00/X2

Drive Connector Motor Phases

0150-3526

DC01-Signal/X4

Drive Connector 24VDC & Logic

0150-3447

DC01-Safety/X33

Drive Connector Safety

0150-3451

RS232 PC config. Cable 2.5m

For C1100/C1250/E1200/E1400/M8000

0150-2143

Isolated USB-serial converter

Isolated USB RS232/422/485 converter

0150-3120

Compatible Power Supplies

Art. No.

S01-72/1000

Power Supply 72V/1000W, 3x340-550VAC

0150-1872

S01-72/500

Power Supply 72V/500W, 1x120/230VAC

0150-1874

S01-48/1000

Power Supply 48V/1000W, 3x340-550VAC

0150-????

S01-48/500

Power Supply 48V/500W, 1x120/230VAC

0150-????

S01-24/1000

Power Supply 24V/1000W, 3x340-550VAC

0150-????

S01-24/500

Power Supply 24V/500W, 1x120/230VAC

0150-????

T01-72/420-Multi

T-Supply 72V/420VA, 3x230/400/480VAC

0150-1869

T01-72/900-Multi

T-Supply 900VA, 3x230/400/480 VAC

0150-1870

T01-72/1500-Multi

T-Supply 1500VA, 3x230/400/480 VAC

0150-1871

T01-72/420 -1ph

T-Supply 420VA, 1x208/220/230/240VAC

0150-1859

ATTENTION: The connectors have to be ordered separately and are not included 
with the drive!

NTI AG / LinMot

®

www.LinMot.com

Page 21/27

C

11

00

 I

n

st

al

la

ti

on

 G

ui

de

Содержание LinMot C1100 Series




























Отзывы: