nStor NexStor 4200F Series Скачать руководство пользователя страница 18

Страница: 18 / 174

Chapter 1 - Getting Started

SES Controller Card

A manual override of the fan speed control is available for special circumstance

environments. Referring to the illustration on the preceding page, two jumpers

are provided on the fan module printed circuit board to override the firmware

control of the fan speeds. This hardware setting provides full voltage to the fans

for maximum operational speed, which is greater than the maximum speed set

by the automatic software control. This configuration is normally used when fan

speed noises are not an issue, and the ambient operating temperature is at or

above 30°C (86°F), thus ensuring that maximum available cooling is being

provided.

The jumpers JP1 and JP2 by default are offset, which enables the automatic fan

speed control. Placing the jumper on both pins for each jumper will override the

automatic setting and configure the fans to maximum power.

SES Controller Card

WARNING:

The SES Controller card is NOT HOT SWAPPABLE. You must POWER

DOWN the enclosure prior to removing or installing this card.

The SES Controller card provides the built-in environmental and system status

monitoring, as well as the switches for setting enclosure ID addresses and drive

spin up options. This card is installed at the rear of the enclosure in the lowest

slot below the two Disk I/O cards.

SES Controller Card

SES CONTR

OLLER

PART NUMBER 0

8-9-963220

ARTW

ORK REVISI

ON -1

JP2

RS-232

A
D
0

A
D
1

A
D
2

S
P
1

S
P
2

B
D
R

D
L
Y

R
M
T

SES

SES Switches

RS-232 Service Port

4200F.book Page 6 Thursday, January 23, 2003 2:47 PM

Содержание NexStor 4200F Series















































































































































































Результаты поиска

Содержание NexStor 4200F Series

Отзывы:

Похожие инструкции для NexStor 4200F Series

Бренды по названию

Популярные бренды

nStor NexStor 4200F Series, Руководство пользователя

Результаты поиска

Содержание NexStor 4200F Series

Отзывы:

Похожие инструкции для NexStor 4200F Series

Бренды по названию

Популярные бренды