nStor NexStor 4200F Series Скачать руководство пользователя страница 131

Страница: 131 / 174

119

Chapter 5

Troubleshooting

This chapter provides typical solutions for problems you may encounter while
operating the NexStor 4200F Series Storage System.

General Enclosure Problems

Symptom

Reason

Solution

Fails to power on.

Power cord(s) not
connected properly.

Power not available at the
outlet.

Power switch not in the
proper position.

Faulty power cord.

Faulty power supply.

Verify that the power cord is properly
connected to the power module.

If the enclosure is plugged into a
three-hole grounded outlet, verify that
power to the outlet has not been
interrupted. This can be accomplished
by testing the outlet with a known
working appliance, like a lamp.

Be sure that the power switch is in the
“On” position, labeled with an “I.”

Replace the power cord.

Identify the failed PSU, see “Replacing
a Power Supply” on page 129.

If the enclosure is not responding,
contact your service provider.

4200F.book Page 119 Thursday, January 23, 2003 2:47 PM

Содержание NexStor 4200F Series















































































































































































Результаты поиска

Содержание NexStor 4200F Series

Отзывы:

Похожие инструкции для NexStor 4200F Series

Бренды по названию

Популярные бренды

nStor NexStor 4200F Series, Руководство пользователя

Результаты поиска

Содержание NexStor 4200F Series

Отзывы:

Похожие инструкции для NexStor 4200F Series

Бренды по названию

Популярные бренды