NSK Megatorque Motor EGA Скачать руководство пользователя

Страница: 2 / 10

1. Preface

This manual describes necessary procedure to perform PB motor operation as a startup guide. Refer manual

M-E099GA0C2-191 for detail.

Please use application software

“

MEGATORQUE MOTOR SETUP

”

to set parameter setting value of model

EGA driver.

“

MEGATORQUE MOTOR SETUP

”

is a free software which can be downloaded from NSK

Website.

(

http://www.nsk.com/

)

2. System configuration

Noise filter

Installed to protect power line from
external noise.

防ぐために取り付けます。

Citcuit Breaker

Used to protect power line.
Turns off the power supply when
overload runs.

MEGATORQUE
MOTOR SETUP

Enables parameter set up and monitoring
through communication with a PC.

Host equipment

Switches power On/Off.
Please place safeguard circuit.

T S R

Electromagnetic contactor

Converter cable

Motor cable

RS-232C

Motor

For high-frequency operation, use an external
regenerative resistor.

External regenerative resistor

Converter

Содержание Megatorque Motor EGA











Результаты поиска

Содержание Megatorque Motor EGA

Отзывы:

Похожие инструкции для Megatorque Motor EGA

Бренды по названию

Популярные бренды

NSK Megatorque Motor EGA, Руководство для стартапов

Результаты поиска

Содержание Megatorque Motor EGA

Отзывы:

Похожие инструкции для Megatorque Motor EGA

Бренды по названию

Популярные бренды