background image

—5—

Signal words:

“DANGER” indicates an imminently 

hazardous situation which, if not avoided, will 

result in death or serious injury. This signal 

word is limited to the most extreme situations.
“WARNING” indicates a potentially 

hazardous situation which, if not avoided, 

could result in death or serious injury.
“CAUTION” indicates a potentially hazardous 

situation which, if not avoided, may result in 

minor or moderate injury. It may also be used 

to alert against unsafe practices.

Safety Symbol

!

 

This international safety symbol is used to 

identify and call attention to specific  

safety matters.

Safety Information

To Avoid Severe Personal Injury or Property 

Damage, read carefully and understand the 

following Safety Precautions.

1. WORk AReA

!

CAUTION

Keep your work area clean and well lit.  

Cluttered benches and dark areas invite 

accidents.

2. PeRSONAL SAFeTY

!

CAUTION

Use safety equipment. Always wear eye 

protection. Dust mask, non-skid safety shoes, 

hardhat, or hearing protection must be used 

for appropriate conditions.

Never alter or remove safety devices.

!

WARNING

Stay alert, watch what you are doing and use 

common sense when operating a tool. Do not 

use tool while tired or under the influence of 

drugs, alcohol, or medication. A moment of 

inattention while operating tools may result in 

serious personal injury.

Dress properly. Do not wear loose clothing 

or jewelry. Contain long hair. Keep your hair, 

clothing, and gloves away from moving parts. 

Loose clothes, jewelry, or long hair can be 

caught in moving parts.

3. TOOL uSe AND CARe

!

CAUTION

Check for misalignment or binding of moving 

parts, breakage of parts, and any other condition 

that may affect the tool’s operation. If damaged, 

have the tool serviced before using. Poorly 

maintained tools cause many accidents.

General Safety Rules   –Save These Instructions–

Содержание Aero 08080





















Отзывы: