Novexx Solutions XLP 514 страница 52 Скачать руководство пользователя

Страница: 52 / 116

User Manual

XLP 514/516

CONNECTIONS

WARNING!
This machine operates using mains voltage! Touching live electrical parts may expose

you to hazardous electrical currents and may lead to burns.
► Make sure that the machine is switched off before connecting the power cable.
► Only connect the machine to a grounded power socket fitted to authorised stan-

dards.
► Only link the machine to devices that fulfil the SELV (safety extra-low voltage) circuit

requirements specified in EN 60950.

CAUTION!
Risk of machine damage due to defective accessories.
► Only connect original accessories.

Fig. 30: Connections at a XLP 51x. Left side: optional BasicIO board; Right side: optional Basic USI board.

Pos. Connection

Application

USB device interfaces (2x)

Used to connect devices, for example keyboard or

scanner or external memory media

USB interface type A (host)

Used to transfer print jobs from a host (for example a

PC); transfer firmware; read service data

Serial interface (RS232)

Used to transfer print jobs from a host (for example a

PC); transfer firmware; read service data

Network connection (Ethernet

10/100/1000)

Used to transfer print jobs from a host (for example a

PC); transfer firmware; read service data; operation via

web server

Power switch

Switches the printer on/off

Connection to the mains power

supply

Power supply

Edition 1 - 8/2021

Product Description

Connections

Содержание XLP 514





















































































































Результаты поиска

Содержание XLP 514

Отзывы:

Похожие инструкции для XLP 514

Бренды по названию

Популярные бренды

Novexx Solutions XLP 514, Руководство пользователя

Результаты поиска

Содержание XLP 514

Отзывы:

Похожие инструкции для XLP 514

Бренды по названию

Популярные бренды