NOVENCO ZERAX AZL-AZN-AZW Скачать руководство пользователя страница 29

Страница: 29 / 30

Novenco ZerAx axial fan types AZL-AZN-AZW

– Installation and maintenance

29 of 30

Appendix - G. Checklists

Before installation

Inspection and maintenance

Turn rotor by hand - it must turn freely

Inspection

Outdoor installations:

Location must be sheltered

• Measure power consumption at ½ and full

speeds

Ground fan to remove static electricity

Clear installation location to ensure free airflows

•

Verify torques of fixation bolts

Install wire guards on front and back of fan (IP20)

•

Measure vibrations on fan casing

• Visual inspection – rotor, casing, silencers and

electric connection

Before start-up

Maintenance

Turn rotor by hand - it must turn freely

•

See

“

Before inspection and maintenance

”

Remove transport rods from support frame

•

Clean the fans

Clear fans and airflow ways

•

Service fans - drain motor, check electrics

Inspect wire guards

•

Replace broken parts

Turn fan on briefly to verify rotational direction

•

Lubricate motor bearings

•

Turn fan on briefly to verify rotational

direction

Start-up

Troubleshooting

Power on fans

Lacking performance

Check for abnormal sounds and vibrations

•

Inlet or outlet blocked

Measure vibrations –

see

“

Vibration levels

” on page

•

Auxiliary fans stopped

After 30 min. operation – check for abnormal sounds

•

Motor defective

•

Motor disconnected

Before inspection and maintenance

•

Electric connection defective

Turn off power for fans

•

Wrong rotational direction of rotor

Disconnect power supply

Lock power switches

Noise and vibrations

•

Motor bearings defective

•

Rotor imbalance

•

Rotor worn or damaged

•

Loose components

•

Wrong rotor blade pitch angles

•

Fan operates in stalling area

Содержание ZERAX AZL-AZN-AZW































Результаты поиска

Содержание ZERAX AZL-AZN-AZW

Отзывы:

Бренды по названию

Популярные бренды

NOVENCO ZERAX AZL-AZN-AZW, Руководство по установке и обслуживанию

Результаты поиска

Содержание ZERAX AZL-AZN-AZW

Отзывы:

Бренды по названию

Популярные бренды