NOVENCO CNA Series Скачать руководство пользователя страница 7

6

Novenco Building & Industry A/S

Industrivej 22

Tel. +45 70 77 88 99

4700 Naestved

www.novenco-building.com

Denmark

8. Attestation of

conformity

EU - Attestation of Conformity

Novenco Building & Industry A/S
Industrivej 22
4700 Naestved
Denmark

Hereby declares that centrifugal fans 
type CNA, CNB, CNA-M and CNB-M 
meet the requirements of the directives 
below, on condition that the products are 
installed in accordance with the instruc-
tions included in the supply. Altering the 
products causes this declaration no 
longer to apply.

Applied directives

– Machinery 2006/42/EU
– ECO design 2009/125/EU
– ECO energy labelling 2010/30/EU
– EMC 2014/30/EU
– LVD 2014/35/EU

Applied standards and regulations

EU 327/2011:

Fans driven by motors with electric 
power between 125 W and 500 kW

EN ISO 12100:2011

Safety of machinery
- General principles for design
- Risk assessment and risk reduction

EN ISO 13857:

Safety of machinery - Safety distances

EN 60204-1:

Safety of machinery - Electrical equip-
ment of machines Part 1: General Re-
quirements

EN 61000-6-2:

EMC - Part 6-2: Generic standards - 
Immunity for industrial environ-
ments

EN 61000-6-3:

EMC - Part 6-3: Generic standards - 
Emission standard for residential, 
commercial and light-industrial envi-
ronments

EN 61800-3, class C2:

Adjustable speed electrical power 
drive systems, EMC requirements 
and specific test methods

It is a condition that Novenco's instruc-
tions for installation have been followed.

Naestved, 01.02.2018

Peter Holt
Technical director
Novenco Building & Industry A/S

Содержание CNA Series









Отзывы: