background image

Installation and Setup

Chapter 2 

SMART-MR10 User Manual Rev 0B 

29

Table 4

 shows the meaning of the LED states in the expected sequence after power is applied. 

Flashing means that the LED is turning on and off at a 1 Hz rate - 0.5 seconds on and 0.5 seconds off.

Debugging Guidelines:

If the power is on but the yellow LED doe not flash within one minute, then no satellites are 
tracking. There may be excessive blockage or the unit may be defective. Make sure the unit has 
an unobstructed view of the sky. Try power cycling the unit.

If the yellow LED does not flash within one minute and power cycling the unit does not fix the 
problem, request a VERSION log to ensure that the auth code is correct.

Example of a receiver loaded with an incorrect auth code:

<ok

[com1]<version com1 0 72.0 unknown 0 12.387 004c0001 3681 5053

<     3

<          gpscard "invalid authcode" "dhc09401009" "mcagtp-1.00-

22b" "3.710" "3.002" "2009/dec/30" "11:20:58"

<          db_userappauto "smartag" "0" "" "1.100" "" "2010/jan/

25" "17:32:44"

<          userinfo "no bt" "" "" "" "" "" ""

[com1]

If the yellow LED is flashing but does not progress to solid yellow within one minute, then 
insufficient satellites are tracking or the signal quality is poor and ephemeris data can’t be 
received. Normally, four satellites are sufficient for a valid position as long as they are widely 

 Table 4:  SMART-MR10 LED Status Indicators

Red

Yellow

Green

Condition

Off

Off

Off

Power is not available. (Red indicator may also not be lit if a 
boot failure has occurred.)

On

Off

Off

Power available but no satellites are being tracked

On

Flashing

Off

Tracking at least one satellite but not a valid position

On

On

Off

Position valid in basic autonomous mode

On

On

Flashing

SBAS tracking, but not enough data for enhanced solution.

On

On

On

Position valid in an enhanced accuracy mode

a

 

(WAAS/EGNOS/MSAS/DGPS, OmniSTAR VBS/XP/HP, or 
RTK)

a. When acting as a reference receiver, all lights on solid indicates a good fixed position.

On

Flashing

Flashing

Fixed position with bad integrity

Содержание SMART-MR10-GENERIC









































































































Отзывы: