Novatel MT 4100 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 55

Novatel MT 4100 Скачать руководство пользователя страница 12

MT 4100 User Guide

8

Power

The MT 4100 accepts 9-32 VDC, minimum 2 amps input power. This allows the device to be used on
both 12 V and 24 V vehicles per SAE specifications, including protection for jump-starting 24 V vehicles.

Pins 17 and 18 on the 22-Pin IO connector are the power input and pins 6 and 7 are ground.

All power and ground pins must be connected.

Power Consumption

Mode

Current

GPS

CDMA BC0 - 800 MHz

< 66 mA @ 14.2 V

GPS off; lowest current consumption while still
being able to contact the device

CDMA BC1 - 1900 MHz

< 63 mA @ 14.2 V

GPS on

Idle (GPS on)

< 54 mA @14.2 V

Registered

Idle (GPS off)

< 33 mA @14.2 V

Registered

Low Power Sleep Mode

<1.3 mA @14.2 V

GPS off

Bench Testing / Programming

WARNING!

After performing a firmware upgrade the device will respond that the firmware load is

complete. However, power must remain applied to the device for approximately two minutes after the
firmware upgrade completion message is received. This allows time for the upgrade to be applied to
the auxiliary processor. The user can confirm it is safe to remove power by sending the AT$OBDVER?
command. If the upgrade is still processing, the device will respond with an error. If the upgrade is
complete, the device will respond with the current software version.

«
...
10
11
12
13
14
...
»

Содержание MT 4100
























































Отзывы:

Нет отзывов