Novanta p400 OEM Series Скачать руководство пользователя страница 96

Страница: 96 / 106

DUTY CYCLE/PULSE WIDTH LIMIT FAULT

PAGE

Symptom:

•

The p400 is connected to a network; however, the p400 web interface does not open or locks up

while receiving data from the laser.

Possible Causes:

•

The p400 laser was connected to the network using a crossover cable.

A straight-through cable is required if connecting an p400 to a network via a network router, switch, or

hub.

•

Java script is not enabled in the web browser.

Locate your browser’s Internet Options menu and configure it to enable Java script. As shown in Figure

below, the Java feature is located on the Internet Options dialog’s Advanced tab (under Tools/Internet

Options). The dialog boxes in your particular browser may appear differently.

Figure 5-2 Enable Java script in browser.

•

Multiple p400’s is connected to the same network with identical IP addresses.

Make sure only one p400 laser is connected to the network at a time or, if multiple p400’s is connected,

be sure they have distinct IP addresses to prevent IP addressing conflicts.

•

The laser’s IP address is not recognized as an authorized site on your local intranet network or a

trusted site on the Internet.

Add the laser’s IP address to the list of authorized and/or trusted websites. In your browser, locate the

Internet Options dialog’s Security tab. The dialog boxes in your particular browser may appear

differently.

Содержание p400 OEM Series











































































































Результаты поиска

Содержание p400 OEM Series

Отзывы:

Бренды по названию

Популярные бренды

Novanta p400 OEM Series, Руководство пользователя

Результаты поиска

Содержание p400 OEM Series

Отзывы:

Бренды по названию

Популярные бренды