Novanta i401 Скачать руководство пользователя страница 111

Страница: 111 / 133

OPERATIONAL FLOWCHART

PAGE

111

Table 5-10 Laser fault codes

The Laser Ready output opens (switches to a high impedance state) when a fault occurs.

A continuously flashing SHT LED indicates a No-Strike condition, and the laser is limited to a

5% duty cycle (at 5 kHz). If the No-Strike condition clears, the laser will recover without

cycling power. Common causes of No-Strike condition (gas breakdown) issues are

environmental conditions—like cold overnight temperatures when the laser is off. In situations

like this, it may take 30 to 60 seconds for gas breakdown to occur and begin normal daily

operation. The Fault Detected output closes for a minimum of 50 ms or until the No-Strike

condition clears.

Web page fault annunciation

The i401 web interface displays errors and warnings in real-time on the home page in either the error

message area or the warning message area. Hard faults that require a DC power cycle are always shown

in the error message area. Operating data is not archived or displayed if the web interface is inactive

when the fault occurs. The event log page displays fault information recorded over the life of the laser.

See the i401 web interface section in the Technical Reference section for web page access details.

Resetting faults

Remote interlock condition

A remote interlock condition occurs when the Remote Interlock input opens (the INT LED changes from

green to red and the Interlock Open output Closes). The internal shutter mechanism closes (even when

the Shutter Open Request input is active) and lasing is halted immediately.

Warning: Serious Personal Injury

i401 OEM lasers, remote interlock faults are not latched. Clearing the fault condition re-

enables the RDY indicator and the laser will fire after the five second delay provided the SHT

indicator is lit and a PWM Command signal is applied. Because exposure to 10.6

m CO2 laser

radiation can inflict severe corneal injuries and seriously burn human tissue, the OEM or

System Integrator must ensure that appropriate safeguards are in place to prevent

unintended lasing.

Содержание i401






































































































































Результаты поиска

Содержание i401

Отзывы:

Похожие инструкции для i401

Бренды по названию

Популярные бренды

Novanta i401, Руководство пользователя

Результаты поиска

Содержание i401

Отзывы:

Похожие инструкции для i401

Бренды по названию

Популярные бренды