background image

40

NFS-320/E/C Installation Manual —

 P/N 52745:M2  7/1/14

Applications

NFPA 72 Proprietary Fire Alarm Systems

4.5  NFPA 72 Proprietary Fire Alarm Systems

When connected and configured as a protected premises unit with UDACT or UDACT-2, the NFS-
320/E will automatically transmit General Alarm, General Trouble, and General Supervisory 
signals to a listed compatible Protected Premises Receiving Unit. See the 

UDACT Manual

 or 

UDACT-2 Manual

 for compatible receiving units. A simplified drawing of connections between the 

receiving unit and the NFS-320/E protected premises unit is shown in Figure 4.4

Connect the receiving unit to the protected premises unit as shown in Section 4.3 “NFPA 72 Central 
or Remote Station Fire Alarm System (Protected Premises Unit)”. 

For information on installing and programming the Receiving unit, refer to the documentation for 
that control panel.

4.6  Fire/Security Applications 

4.6.1  General Operation

The control panel can be used as a combination Fire/Security system when installed and operated 
according to the instructions in this section.

For security applications, program one or more monitor modules (listed for security applications) 
with the 

SECURITY

 Type Code, and wire as shown in Figure 4.6. Activating this type of module 

lights the 

SECURITY

 LED, and displays a security alarm condition on the control panel LCD display. 

The panel sounder will sound until the Security alarm is acknowledged. You can also program 
additional sounders or output devices to activate with the security alarm initiating device. The 

SECURITY

 Type Code is designed to indicate an alarm as follows: (a) on an open or short circuit; or 

(b) on a ±50% change in resistance value from the End-of-Line resistor value.

A tamper switch installed in the cabinet door will indicate a door tamper condition whenever the 
door is open. If the control panel indicates a Security alarm, you can acknowledge, silence, and 
reset the condition from the control panel.

When the system resets, a 30-second exit timer starts. During this time the tamper switch and all 
Security alarms are ignored. There is no entrance delay timer.

NOTE:

NFS-320/E/C is not approved for use in security applications in Canada. 

NFS-320/E 

Protected Premises Unit

Compatible Receiving Unit 

(see 

UDACT Manual

 or 

UDACT-2 

Manual

)

Telephone line and backup

UDACT

or UDACT-2

NFS-320/E

Figure 4.4  Typical Proprietary Fire Alarm Systems Wiring Connections

Содержание NFS-320

































































Отзывы: