997-417, Issue 2 June 2002
Jumper Links
Jumper Links
The 64 output channels are arranged in two banks of 32. Each bank is
arranged in four groups of 8 outputs. Each group is provided with a
jumper link which configures the group to drive either LEDs or relays:
JUMPER LINK FITTED = GROUP DRIVES RELAYS
JUMPER LINK NOT FITTED = GROUP DRIVES LEDs
The groups can be configured independently, i.e. within a bank some
groups may drive relays and others may drive LEDs.
CAUTION:
Ensure that jumper links are configured correctly. If an LED is
connected to an output for which the link is fitted, the LED will
have a short life expectancy. Conversely, if a relay is connected
to an output for which the link is not fitted, the relay will not
operate.
The 64 output channels are arranged in two banks of 32. Each bank is
arranged in four groups of 8 outputs. Each group is provided with a
jumper link which configures the group to drive either LEDs or relays:
JUMPER LINK FITTED = GROUP DRIVES RELAYS
JUMPER LINK NOT FITTED = GROUP DRIVES LEDs
The groups can be configured independently, i.e. within a bank some
groups may drive relays and others may drive LEDs.
CAUTION:
If an LED is
connected to an output for which the link is fitted, the LED will
have a short life expectancy. Conversely, if a relay is connected
to an output for which the link is not fitted, the relay will not
operate.
Ensure that jumper links are configured correctly.
Procedure for Fitting a Mimic Driver
Assembly (typical)
Procedure for Fitting a Mimic Driver
Assembly (typical)
Procedure for Fitting a Mimic Driver
Termination Assembly (typical)
Procedure for Fitting a Mimic Driver
Termination Assembly (typical)
Proceed as follows:
1
Find a suitable location to install the mimic driver PCB assembly
(H), such as a third-party-supplied enclosure. Four fixing holes (I)
are provided. Mark and drill the surface where the assembly is to
be mounted to take suitable 4mm-sized screws (not supplied).
2
Fit the assembly and secure with the 4mm screws. The assembly
can be mounted vertically or horizontally.
3
Refer to the section at the bottom of this page for all required
cable and wiring connections.
Proceed as follows:
Find a suitable location to install the mimic driver PCB assembly
(H), such as a third-party-supplied enclosure. Four fixing holes (I)
are provided. Mark and drill the surface where the assembly is to
be mounted to take suitable 4mm-sized screws (not supplied).
Fit the assembly and secure with the 4mm screws. The assembly
can be mounted vertically or horizontally.
Refer to the section at the bottom of this page for all required
cable and wiring connections.
1
2
3
Proceed as follows:
1
Find a suitable location to install the mimic driver termination PCB
assembly (J). To keep the LED wiring as short as possible, locate
the mimic driver termination board(s) close to the LEDs. An
option of four ‘flat-mounting’ holes (K) and/or two ‘edge-on-
mounting’ holes (L) are provided for fitting convenience. Mark
and drill the surface where the assembly is to be mounted to take
suitable 4mm-sized screws (not supplied).
2
Fit the assembly and secure with the 4mm screws. The assembly
can be mounted vertically or horizontally.
3
Refer to the next section for wiring and LED connections.
Proceed as follows:
Find a suitable location to install the mimic driver termination PCB
assembly (J). To keep the LED wiring as short as possible, locate
the mimic driver termination board(s) close to the LEDs. An
option of four ‘flat-mounting’ holes (K) and/or two ‘edge-on-
mounting’ holes (L) are provided for fitting convenience. Mark
and drill the surface where the assembly is to be mounted to take
suitable 4mm-sized screws (not supplied).
Fit the assembly and secure with the 4mm screws. The assembly
can be mounted vertically or horizontally.
Refer to the next section for wiring and LED connections.
1
2
3
H
H
II
M
M
II
II
II
J
J
K (x4)
K (x4)
L (x2)
L (x2)
2
Installing the IDR-MD Mimic Driver Kit
(Continued)
MIMIC DRIVER PCB
MIMIC DRIVER PCB
124-320
124-320
IN
IN
OUT
OUT
JP5
JP5
BANK 1
OUTPUTS
1-8
BANK 1
OUTPUTS
1-8
Mimic Driver Board
Mimic Driver Board
JP8
JP8
JP1
JP1
JP4
JP4
JP6
JP6
JP7
JP7
JP2
JP2
JP3
JP3
BANK 1
OUTPUTS
9-16
BANK 1
OUTPUTS
9-16
BANK 1
OUTPUTS
17-24
BANK 1
OUTPUTS
17-24
BANK 1
OUTPUTS
25-32
BANK 1
OUTPUTS
25-32
BANK 2
OUTPUTS
1-8
BANK 2
OUTPUTS
1-8
BANK 2
OUTPUTS
9-16
BANK 2
OUTPUTS
9-16
BANK 2
OUTPUTS
17-24
BANK 2
OUTPUTS
17-24
BANK 2
OUTPUTS
25-32
BANK 2
OUTPUTS
25-32
!!
