background image

© Copyright 2017, Sunex Tools®

 1 

rev. 

 11/17/17

Model  NSJ0301

3 Ton Capacity Aluminum Service Jack

For Technical Questions, Call: 1-800-879-7316

WARNING INFORMATION

This is the safety alert symbol. It is used to alert you 

to potential personal injury hazards. Obey all safety 

messages that follow this symbol to avoid possible 

injury or death.

 

             

IMPORTANT: READ THESE INSTRUCTIONS BEFORE OPERATING

BEFORE USING THIS JACK, READ THIS MANUAL COMPLETELY AND THOROUGHLY, UNDERSTAND ITS OPERATING

PROCEDURES, SAFETY WARNINGS AND MAINTENANCE REQUIREMENTS.

It is the responsibility of the owner to make sure all personnel read this manual prior to using this jack. It is also the responsibility of the jack owner to 

keep this manual intact and in a convenient location for all to see and read. Contact Sunex for a replacement label if your jack's label is not readable. 

If the operator is not fluent in English, the product and safety instructions shall be read to and discussed with the operator in the operator's native 

language by the purchaser/owner or his designee, making sure that the operator comprehends its contents.

THE NATURE OF HAZARDOUS SITUATIONS

The use of portable automotive lifting and support devices is subject to certain hazards that cannot be prevented by mechanical means, but only 

by the exercise of intelligence, care, and common sense. It is therefore essential to have owners and personnel involved in the use and operation 

of the equipment who are careful, competent, trained, and qualified in the safe operation of the equipment and its proper use. Examples of hazards 

are dropping, tipping or slipping of loads caused primarily by improperly secured loads, overloading, off-centered loads, use on other than hard level 

surfaces, and using equipment for a purpose for which it was not designed.

METHODS TO AVOID HAZARDOUS SITUATIONS

    •  Read, study, understand and follow all instructions before operating this device.

    •  Inspect the jack before each use. Do not use jack if damaged, altered, modified, in poor condition, leaking hydraulic fluid, or unstable due  

    to loose or missing components. Make corrections before using.

    •  Lift only on areas of the vehicle as specified by the vehicle manufacturer.

    •  User and bystanders must wear eye protection that meets ANSI Z87.1 and OSHA standards.

    •  Do not use jack beyond its rated capacity. Do not shock load.

  • 

This is a lifting device only. Immediately after lifting, support the vehicle with jack stands capable of sustaining the load before  

    working on the vehicle.

    •  Use only on a hard level surface free from obstructions so the jack is free to reposition itself during lifting and lowering operations.

    •  Center load on saddle. Be sure setup is stable before working on vehicle.

    •  Do not move or dolly the vehicle while on the jack.

    •  Do not use any materials that may serve as risers, spacers or extenders between the stock lifting saddle and the load.

    •  Do not use any adaptors that replace the stock lifting saddle unless approved or supplied by Sunex.

    •  Always lower the jack slowly and carefully.

    •  Do not use (or modify) this product for any other purpose than that for which it was designed without consulting the manufacturer's  

 

    authorized representative.

    •  This product may contain one or more chemicals known to the State of California to cause cancer and birth defects or other reproductive  

   harm. 

Wash hands thoroughly after handling.

    •  Failure to heed these warnings may result in fatal personal injury and/or property damage.

CONSEQUENCES OF NOT AVOIDING HAZARDOUS SITUATIONS

Failure to read this manual completely and thoroughly, failure to understand its OPERATING INSTRUCTIONS, SAFETY WARNINGS, 

MAINTENANCE INSTRUCTIONS and comply with them, and failure to comply with the METHODS TO AVOID HAZARDOUS SITUATIONS could 

cause accidents resulting in serious or fatal personal injury and/or property damage.

WARNING: Indicates a hazardous situation 

which, if not avoided, could result in death 

or serious injury.

WARNING

WARNING

WARNING

WARNING

Complies with 

ASME PASE-2014

Safety Standard

Отзывы: