manualshive.com logo in svg

Norwood The Grain Handler 10, Руководство оператора, Страница: 60 / 130

Поделиться
Скачать
Norwood The Grain Handler 10 Скачать руководство пользователя страница 60

3 - INSTALLATION

3-20

(Qty. 4) "3/8-16 Flange Nuts" 48

, & 

"3/8 Flat Washers"

 

49

. 

(See Fig. # 3-46)

Fig. # 3-46 Horizontal Powerhead Installation Step # 10

49

47

48

11.  Install the 

"Lower Sheave" 50

, & 

"Keystock" 51

 onto 

the 

"Horizontal Powerhead Input Shaft" 52 .  

Do not 

tighten the setscrews at this time. 

NOTE

Power  Sweep  Sheaves  differ  in  size  depending  on  bin 

diameter, powerhead option, & motor size & type, but in

-

stallation should be approximately the same.

52

51

50

Fig. # 3-47 Horizontal Powerhead Installation Step # 11

12. From the table below, 

(See Fig. # 3-48)

 determine the 

NEMA  frame  designation  from  the  electric  motor  de

-

scription you wish to install.  (

Example:

 Motor, 12.5HP 

1-Phase, 215T TEFC Ø1-3/8” Shaft).  The "215T" is the 

part of the description we will focus on. 

(See Fig. # 3-48) 

(See Fig. # 3-49)

Fig. # 3-48 Table: Electric Motors

Electric Motors

PART  

NUMBER

DESCRIPTION

QTY.

Single Phase Motors (230-460 Volt)

90-46-7017 Motor, 3HP 1-Phase, 182T TEFC Ø1-1/8” Shaft

1

90-46-7003 Motor, 5HP 1-Phase, 184T TEFC Ø1-1/8” Shaft

1

90-46-7004 Motor, 7.5HP 1-Phase, 213T TEFC Ø1-3/8” Shaft

1

90-46-7013 Motor, 10hp 1-Phase, 215T TEFC Ø1-3/8” Shaft

1

90-46-7009 Motor, 12.5HP 1-Phase, 215T TEFC Ø1-3/8” Shaft

1

Three Phase Motors (230-460 Volt)

90-46-7018 Motor, 3HP 3-Phase, 182T TEFC Ø1-1/8” Shaft

1

90-46-7002 Motor, 5HP 3-Phase, 184T TEFC Ø1-1/8” Shaft

1

90-46-7019 Motor, 7.5HP 3-Phase, 213T TEFC Ø1-3/8” Shaft

1

90-46-7016 Motor, 10HP 3-Phase, 215T TEFC Ø1-3/8” Shaft

1

90-46-7010 Motor, 15HP 3-Phase, 254T TEFC Ø1-5/8” Shaft

1

90-46-7020 Motor, 20HP 3-Phase, 256T TEFC Ø1-5/8” Shaft

1

13. From the table below, 

(See Fig. # 3-49) 

use the dimen-

sions provided to determine the correct slots that will be 

used for mounting the motor. 

(See Fig. # 3-50)(See Fig. 

# 3-51)

NEMA 

FRAME

D

E

E(X2)

2F

182T

4-1/2”

3-3/4”

7-1/2"

4-1/2”

184T

4-1/2”

3-3/4”

7-1/2"

5-1/2”

213T

5-1/4”

4-1/4”

8-1/2"

5-1/2”

215T

5-1/4”

4-1/4”

8-1/2"

7

254T

6-1/4”

5

10"

8-1/4”

256T

6-1/4”

5

10"

10”

Fig. # 3-49 Table: NEMA Quick Reference Chart

 

Содержание The Grain Handler 10



































































































































Отзывы:

Нет отзывов