Norwood The Grain Handler 10 Скачать руководство пользователя страница 19

Страница: 19 / 130

2 - SAFETY INFORMATION

2-7

Grain Bin Safety Contd.

Grain Bin Entry Safety

The information in this section applies to entry through any

access point.

Always try to work and solve problems without entering a bin.

WARNING

If you must enter the bin, follow the safety information below

to safely enter through the roof, door or any access point:

• Stop the unloading process if the bin is being unload

ed and lockout/tagout power before entering the bin,

refer to Lockout/Tagout Safety.

(See"Lock-Out Tag-Out

Safety" on page 2-7)

• Always wear a dust-filtering respirator when entering the

bin. Grain dust and spores when inhaled into the lungs

can cause severe reactions leading to hospitalization in

some cases. Persistent exposure may cause “farmer’s

lung,” which can eventually be fatal.

• Before working inside the bin, ventilate the area by

opening the vent or by other equivalent means to force

air into the bin to prevent oxygen-deficient atmosphere.

Inadequate oxygen is very harmful to your health and

can cause death. Exposure to carbon dioxide can

cause drowsiness, headache and even death due to

suffocation. Test the atmosphere. If the carbon dioxide

hazard cannot be reduced or eliminated or you cannot

test the atmosphere, use correctly fitted and appropriate

respirator.

• Never walk on grain to make it flow.

FAILURE TO HEED THE WARNINGS ABOVE AND ENTER

THE GRAIN BIN MAY CAUSE SERIOUS INJURY OR DEATH

Roof Entry

The information in this section applies to entry through the

bin roof only.

• Never enter a bin from the roof if you don’t know its

unloading history. Bridges of stored material can form

above a void space below, causing potential for entrap

ment.

• Have body harness tethered to a lifeline controlled by

two others outside the bin. One worker should be able

to see inside worker through the inspection hatch. If

there is an accident, one worker can focus on the victim

while the other goes/calls for help.

Lock-Out Tag-Out Safety

Before you start servicing the machine:

Disconnect and lockout power supply, and wait for all moving

parts to stop before servicing, repairing or unplugging any

area of the machine

Attach a

“Do Not Operate”

warning tag to the machine in an

area that will be visible.

do not

operate

signed by

date

WARNING

1. Establish a formal Lock-Out Tag-Out program for your

operation.

2. Train all operators and service personnel before allowing

them to work around the area.

3. Provide tags on the machine and a sign-up sheet to record

tag out details.

Non-Permissible Use

CAUTION

Working on an uncleaned and non-maintained machine

poses unnecessary danger and is therefore forbidden.

Pay attention to the following applications for which the

machine is not suitable:

Machine usage to move non-agricultural grains.

Machine usage to move gravel or large rocks.

Содержание The Grain Handler 10



































































































































Результаты поиска

Содержание The Grain Handler 10

Отзывы:

Norwood The Grain Handler 10, Руководство оператора, Страница: 19 / 130

Результаты поиска

Содержание The Grain Handler 10

Отзывы: