Norwood Kwik-Till HSD1600 Скачать руководство пользователя страница 133

Страница: 133 / 152

6 - TROUBLESHOOTING

6-1

6.0 - TROUBLESHOOTING

Troubleshooting Field Problems

Problem

Possible Cause

Solution

Machine does not

track straight.

Machine not level from front to back.

Adjust hitch link height to the tractor drawbar
Add a depth stop to rear attachment cylinders
Reduce machine tracking spacing for more

overlap
Adjust AutoTrac to the left
Adjust AutoTrac to the right

Add a depth stop to wheel strut cylinders

Full machine plugs.

Ground speed too low.

Increase speed as specified in operations.

Working depth too deep.

Set for (2-3 in) in spring and (3.5-4.5) in for fall

Wings Plug.

Wings not level.

Verify that main and wing cylinders are in float.
Verify that cylinder stops are consistent with the

main frame
Reduce digging depth.

Reduce speed to 10.5 mph (17 km/h).

Furrow on the left

side.

Soil not filling cut.

Increase machine speed to 10.5 mph (17 km/h).
Adjust deflector towards the rear rank.
Make certain that deflector is not running in the

soil.

Surface finish

unsatisfactory.

Speed too low.

Increase machine speed to 10.5 mph (17 km/h).

Subsurface ridges.

Machine unlevel.

Verify that depth stops and hitch link are adjusted

properly.

Deflector plugging.

Too much residue.

During Fall tillage or high residue flip deflector

up.

Residue flow

unsatisfactory.

Adjust front rank.

In high residue, it may be necessary to raise

front rank.

Содержание Kwik-Till HSD1600

























































































































































Результаты поиска

Содержание Kwik-Till HSD1600

Отзывы:

Norwood Kwik-Till HSD1600, Руководство оператора, Страница: 133 / 152

Результаты поиска

Содержание Kwik-Till HSD1600

Отзывы: