©MMXVI NORWECO, INC. NORWALK, OHIO U.S.A.
MANUFACTURED BY
NORWECO, INC.
NORWALK, OHIO
U.S.A. 44857
www.norweco.com
SERVICE PRO
®
WASP START-UP AND OPERATION (Cont.)
8. If the CYCLE TIMER mode has been selected, press
the right arrow button on the touchpad to set the pump
on time. This is the length of time that the pump will
operate each cycle.
a. “PUMP CYCLE ON TIME” and “SET HOURS” will
be displayed on the screen. Press the up or down
arrow button to set the desired hours value.
b. Once the correct hours value has been set, press
the right arrow button to set the minutes value. The
display will read “SET MINUTES”. Press the up
or down arrow button to set the desired minutes
value.
c. Once the correct minutes value has been set, press
the right arrow button to set the seconds value. The
display will read “SET SECONDS”. Press the up
or down arrow button to set the desired seconds
value.
d. Once the correct seconds value has been set,
press the right arrow button to set the pump
off time. “PUMP CYCLE OFF TIME” and “SET
HOURS” will be displayed on the screen. Press the
up or down arrow button to set the desired hours
value.
e. Once the correct hours value has been set, press
the right arrow button to set the minutes value. The
display will read “SET MINUTES”. Press the up
or down arrow button to set the desired minutes
value.
f. Once the correct minutes value has been set, press
the right arrow button to set the seconds value. The
display will read “SET SECONDS”. Press the up
or down arrow button to set the desired seconds
value.
9. Press the right arrow button on the touchpad to enter the
auxiliary input alarms configuration screen. The display
will read “AUXILIARY ALARMS” and the AUX1 value
should be selected. Press the up or down arrow button
to change the auxiliary 1 input from N-OP (normally
open) to N-CL (normally closed) if required. If auxiliary
input 1 will not be used, leave AUX1 set to N-OP.
10. Once auxiliary input 1 has been configured, press the
right arrow button on the touchpad to configure auxiliary
input 2. The AUX2 value should be selected. Press the
up or down arrow button to change the auxiliary 2 input
from N-OP (normally open) to N-CL (normally closed)
if required. If auxiliary input 2 will not be used, leave
AUX2 set to N-OP.
11. Once auxiliary input 2 has been configured, press the
right arrow button on the touchpad to configure auxiliary
input 3. The AUX3 value should be selected. Press the
up or down arrow button to change the auxiliary 3 input
from N-OP (normally open) to N-CL (normally closed)
if required. If auxiliary input 3 will not be used, leave
AUX3 set to N-OP.
12. Press the right arrow button on the touchpad to exit
the programming menu. The display should read
“SERVICE PRO OK” on the top line. The Service Pro
WASP control center programming is complete and the
system is now ready for operation.
VIEW SYSTEM STATUS AND CONFIGURATION
The Service Pro WASP control center records parameters
regarding the Singulair system that can be reviewed at any
time. Adjustments to the programming can be made as
required. To review recorded data and system parameters:
1. Press the “SELECT” button on the touchpad. The
screen should display the elapsed pump run time.
2. Press the right arrow button to review the pump cycle
count.
3. Press the right arrow button to review the aerator
elapsed run time.
4. Press the right arrow button to review the aerator cycle
count.
5. Press the right arrow button to review the auxiliary input
configurations.
6. Press the right arrow button to review failsafe mode
status, software version and panel serial number.
7. Press the right arrow button to exit the system
parameters menu.
PUMP TEST
The Service Pro WASP control center has a built-in pump
test feature. To start a pump test, hold the “PUMP TEST”
button for five seconds. The screen will display “PUMP
TEST” and the pump will turn on. The pump will operate
for five minutes and then will turn off.
ALARM TEST
The Service Pro WASP control center has a built-in alarm
test feature. To start an alarm test, hold the “ALARM
RESET” button for five seconds. The screen will display
“ALARM TEST” and the audible and visual alarms will
turn on for five seconds. After five seconds, the alarms
will turn off.
ALARM CONDITIONS
If the Service Pro WASP control center detects an abnormal
condition, the display will indicate the specific problem
the system is experiencing. For example, if the aerator is
drawing high amps, the display will read “AERATOR HIGH
CURRENT.” To silence the alarms and attempt to clear
the alarm condition, press the “ALARM RESET” button. If
the issue has been corrected, the system will turn off the
alarms and resume normal operation. If a problem still
exists, the audible alarm will be silenced for 48 hours, but
the visual alarm will continue to light. In addition, detailed
information regarding the specific problem will be displayed
on the screen.
