NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2 Скачать руководство пользователя страница 7

Страница: 7 / 112

NAVIGAT X Mk 2

056341 Rev. AA

Safety Precautions

The following safety notice conventions are followed throughout this manual:

Warning

contains an operating or maintenance procedure, practice, condition, statement,

etc., which, if not strictly observed, could result in injury or death of personnel.

Special warning symbols are used in this manual to indicate

Danger from toxic substances,

Danger of electrical shock.

Caution

contains an operating or maintenance procedure, practice, condicion, statement,

etc., which, if not strictly observed, could result in damage to, or destruction of equipment.

Special caution symbols are used in this manual to indicate

Sensitivity of components to electric discharge.

Note

contains an essential operating or maintenance procedure, condition or statement

which is considered importnt enough to be highlighted.

Warning

Careless or improper use of this system may result in vessel damage and/or
SERIOUS INJURY OR DEATH.

Before using this system, operators must be appropriately trained and familiar
with the warnings, safety instructions contained in this manual and on system
components.

Always keep system manuals in a well-known, readily available location.

Caution

Never

exceed specified system power or environmental limits.

Only

trained Sperry Marine service personnel is authorized to provide service

or make repairs to this system.

Never

install unauthorized additional components into this system

Never

make unauthorized modifications to this system

Содержание Sperry Marine NAVIGAT X MK 2
















































































































Результаты поиска

Содержание Sperry Marine NAVIGAT X MK 2

Отзывы:

Похожие инструкции для Sperry Marine NAVIGAT X MK 2

Бренды по названию

Популярные бренды

NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2, Руководство по сборке

Результаты поиска

Содержание Sperry Marine NAVIGAT X MK 2

Отзывы:

Похожие инструкции для Sperry Marine NAVIGAT X MK 2

Бренды по названию

Популярные бренды